Restored 42-321

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Restored 42-321

andrekp
Junior Member

Posts: 12
Threads: 1
Joined: Aug 2009

#16

09-15-2009, 04:22 PM

BTW, my testing suggests that the local oscillator is faily close to being right on. Using a digital radio, the 42-324 tuned to just barely under 600, oscillates the digital at 1060, while the 42-321 tuned to about 1000, oscillates the digital at 1450. However, 1700 on the digital is oscillated by about 1210 on the 42-321 (which is obviously off by about 30-40kc)

So to me, this implies that my local oscillator is probably acting as it should - and is close to 455kc, but that for some reason the upper part of the band is off.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Restored 42-321 - by andrekp - 08-19-2009, 08:37 AM

Re: Restored 42-321 - by codefox1 - 08-19-2009, 04:17 PM

Re: Restored 42-321 - by andrekp - 08-20-2009, 08:19 AM

Re: Restored 42-321 - by Ron Ramirez - 08-21-2009, 08:21 PM

Re: Restored 42-321 - by andrekp - 08-25-2009, 05:20 PM

Re: Restored 42-321 - by codefox1 - 08-26-2009, 12:05 AM

Re: Restored 42-321 - by Ron Ramirez - 08-26-2009, 06:46 AM

Re: Restored 42-321 - by andrekp - 09-09-2009, 12:29 PM

Re: Restored 42-321 - by Raleigh - 09-09-2009, 01:26 PM

Re: Restored 42-321 - by exray - 09-09-2009, 05:38 PM

Re: Restored 42-321 - by andrekp - 09-10-2009, 08:56 AM

Re: Restored 42-321 - by andrekp - 09-14-2009, 12:17 PM

Re: Restored 42-321 - by exray - 09-15-2009, 06:59 AM

Re: Restored 42-321 - by andrekp - 09-15-2009, 12:03 PM

Re: Restored 42-321 - by andrekp - 09-15-2009, 01:32 PM

Re: Restored 42-321 - by andrekp - 09-15-2009, 04:22 PM

Re: Restored 42-321 - by exray - 09-15-2009, 05:24 PM

Re: Restored 42-321 - by andrekp - 09-16-2009, 11:59 AM

Re: Restored 42-321 - by exray - 09-16-2009, 06:39 PM

Re: Restored 42-321 - by andrekp - 09-17-2009, 09:09 AM

Re: Restored 42-321 - by Ron Ramirez - 09-17-2009, 11:17 AM

Re: Restored 42-321 - by andrekp - 09-17-2009, 01:52 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old. My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum. Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

Who's Online

There are currently 2909 online users. [Complete List]
» 1 Member(s) | 2908 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me