Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Unknown Gilfillan Model
#17

I attached a spool of antenna wire. I slowly powered it up on the variac, and didn't get anything, then I realized the variac wasn't plugged in.  Icon_crazy
I plugged it in, and tried again. I wasn't sure which thumbscrew to attach the antenna to. 1st attempt, I got audio, but no radio signals, so I powered down and tried the other screw. Upon power-up, I immediately got static, so I dialed across the band. Everything came in on the dial where it should, so I didn't perform an alignment. For this video, I attached a 12 foot length of wire, and plugged it into my outside wire which runs 50-75 feet out in the backyard. This is a little cheap 4-tuber, so it doesn't have AVC. It's really obvious as I tune across the dial....

[Video: https://youtu.be/ewMVZBNpLPw]

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning


Messages In This Thread
Unknown Gilfillan Model - by PhilcoPhan1936 - 01-19-2016, 02:22 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 01-19-2016, 02:29 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 01-19-2016, 02:34 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 01-19-2016, 02:45 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 01-19-2016, 02:52 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 01-19-2016, 02:57 AM
RE: Unknown Gilfillan Model - by mikethedruid - 01-19-2016, 05:13 AM
RE: Unknown Gilfillan Model - by Arran - 01-19-2016, 05:41 AM
RE: Unknown Gilfillan Model - by Eliot Ness - 01-19-2016, 08:53 PM
RE: Unknown Gilfillan Model - by Paul Philco322 - 01-19-2016, 09:52 PM
RE: Unknown Gilfillan Model - by Arran - 01-20-2016, 02:58 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 09-11-2016, 01:03 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 09-11-2016, 01:07 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 09-11-2016, 01:19 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 09-11-2016, 01:20 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 09-11-2016, 01:24 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 09-11-2016, 02:29 AM
RE: Unknown Gilfillan Model - by OldRestorer - 09-11-2016, 08:10 AM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 07-12-2017, 12:59 AM
RE: Unknown Gilfillan Model - by OldRestorer - 07-12-2017, 11:30 AM
RE: Unknown Gilfillan Model - by Eliot Ness - 07-12-2017, 01:42 PM
RE: Unknown Gilfillan Model - by PhilcoPhan1936 - 07-13-2017, 02:11 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM

[-]
Who's Online
There are currently 7890 online users. [Complete List]
» 3 Member(s) | 7887 Guest(s)
AvatarAvatarAvatar

>