1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-93 hot resister
philco phan
Member
***
Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.
#2

08-20-2009, 03:28 PM
hi,lift the end of the 200 ohm resistor connected to the electrlytic cap and retest,if o.k.,short is towards the left on schematic,if still getting hot short is towards output tube.
phil
Find
« Next Oldest | Next Newest »


Messages In This Thread
37-93 hot resister - by Zapped - 08-20-2009, 03:07 PM
Re: 37-93 hot resister - by philco phan - 08-20-2009, 03:28 PM
Re: 37-93 hot resister - by Zapped - 08-20-2009, 10:53 PM
Re: 37-93 hot resister - by philco phan - 08-21-2009, 10:38 AM
Re: 37-93 hot resister - by Terry Burns - 08-21-2009, 10:57 AM
Re: 37-93 hot resister - by Zapped - 08-21-2009, 03:36 PM
Re: 37-93 hot resister - by philco phan - 08-21-2009, 04:39 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 12:09 AM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 12:57 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 01:51 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:07 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 02:12 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:25 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:34 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 03:34 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 04:01 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 05:50 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 07:08 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 08:15 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 08:26 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM

[-]
Who's Online
There are currently 5558 online users. [Complete List]
» 1 Member(s) | 5557 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration