1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-93 hot resister
philco phan
Member
***
Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.
#9

08-22-2009, 12:57 PM
with everything hooked up,measure ohms from g3 terminal on the socket,tube removed,to ground.
what do you measure?then measure from the same terminal to the electrolytic,what do you have there?
phil
Find
« Next Oldest | Next Newest »


Messages In This Thread
37-93 hot resister - by Zapped - 08-20-2009, 03:07 PM
Re: 37-93 hot resister - by philco phan - 08-20-2009, 03:28 PM
Re: 37-93 hot resister - by Zapped - 08-20-2009, 10:53 PM
Re: 37-93 hot resister - by philco phan - 08-21-2009, 10:38 AM
Re: 37-93 hot resister - by Terry Burns - 08-21-2009, 10:57 AM
Re: 37-93 hot resister - by Zapped - 08-21-2009, 03:36 PM
Re: 37-93 hot resister - by philco phan - 08-21-2009, 04:39 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 12:09 AM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 12:57 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 01:51 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:07 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 02:12 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:25 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:34 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 03:34 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 04:01 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 05:50 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 07:08 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 08:15 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 08:26 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration