1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-93 hot resister
Zapped
Junior Member
**
Posts: 11
Threads: 2
Joined: Aug 2009
#10

08-22-2009, 01:51 PM
Phil

G3 pin to ground is 61.5 ohms
G3 pin to electrolytic is 150 ohms

Thanks for taking the time to help out.
Find
« Next Oldest | Next Newest »


Messages In This Thread
37-93 hot resister - by Zapped - 08-20-2009, 03:07 PM
Re: 37-93 hot resister - by philco phan - 08-20-2009, 03:28 PM
Re: 37-93 hot resister - by Zapped - 08-20-2009, 10:53 PM
Re: 37-93 hot resister - by philco phan - 08-21-2009, 10:38 AM
Re: 37-93 hot resister - by Terry Burns - 08-21-2009, 10:57 AM
Re: 37-93 hot resister - by Zapped - 08-21-2009, 03:36 PM
Re: 37-93 hot resister - by philco phan - 08-21-2009, 04:39 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 12:09 AM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 12:57 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 01:51 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:07 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 02:12 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:25 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:34 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 03:34 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 04:01 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 05:50 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 07:08 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 08:15 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 08:26 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration