1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-93 hot resister
philco phan
Member
***
Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.
#11

08-22-2009, 02:07 PM
lift c17, end towards b+ and retest with everything else connected,tube still removed,does 200 ohm still get hot?
phil
Find
« Next Oldest | Next Newest »


Messages In This Thread
37-93 hot resister - by Zapped - 08-20-2009, 03:07 PM
Re: 37-93 hot resister - by philco phan - 08-20-2009, 03:28 PM
Re: 37-93 hot resister - by Zapped - 08-20-2009, 10:53 PM
Re: 37-93 hot resister - by philco phan - 08-21-2009, 10:38 AM
Re: 37-93 hot resister - by Terry Burns - 08-21-2009, 10:57 AM
Re: 37-93 hot resister - by Zapped - 08-21-2009, 03:36 PM
Re: 37-93 hot resister - by philco phan - 08-21-2009, 04:39 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 12:09 AM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 12:57 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 01:51 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:07 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 02:12 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:25 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:34 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 03:34 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 04:01 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 05:50 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 07:08 PM
Re: 37-93 hot resister - by Zapped - 08-22-2009, 08:15 PM
Re: 37-93 hot resister - by philco phan - 08-22-2009, 08:26 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration