1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 42-1010 Veneer - European Walnut?
AVSorrell
Member
***
Posts: 76
Threads: 18
Joined: Nov 2015
City: Palmyra State, Province, Country: Virginia
#1

10-01-2016, 10:13 AM
Hi Guys -

I have a Philco 42-1010 that has some lost veneer that I am going to replace. One the below photo it is the area on the front below the grille that looks obvious in its veneer loss. Anyhow I gently pulled some more of the loose stuff off to look at the back. Is this the European walnut veneer Philco liked to use?  I will attach some photos below. Thanks for the advice! -- Andy

https://flic.kr/p/MHPRau
Full Radio

https://flic.kr/p/MDrf2M
Close up of Area

https://flic.kr/p/LPqm6H
finished side on veneer

https://flic.kr/p/MAM5Hq
unfinished side
Andy Sorrell
Palmyra, Virginia
(This post was last modified: 10-01-2016, 10:18 AM by AVSorrell.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 42-1010 Veneer - European Walnut? - by AVSorrell - 10-01-2016, 10:13 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6000 online users. [Complete List]
» 1 Member(s) | 5999 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration