Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Couple of Nationals for Terry
#4

Hey Tom,
Long time no post!!!
I had a RAO (oh my back) 7 a few years ago. Need a lot of work and gave to a friend. Designed to drive fones so the output stage is a bit wimpy to drive a 600 ohm spkr. The military was concerned abt rf radiation from the local osc and being tracked down by DF equipment so the rf amp was added to cut down on the radiation. Plus that stinken heavy steel cabinet. Still have a few sliding catacomb sets  NC-81, NC-100X and a NC-200. I'm getting to the place I can't pick those heavy sets up anymore. The HRO's are nice as everything is separate, p/s, spkr, coils so the set it self is pretty manageable for me. The SW-3's are even better there only abt 10#s.
Hope all is well in Clayton. Didn't see you when you might have been up in my neck of the woods a couples of weeks ago.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Couple of Nationals for Terry - by TA Forbes - 10-03-2016, 10:55 PM
RE: Couple of Nationals for Terry - by vecher - 10-03-2016, 11:38 PM
RE: Couple of Nationals for Terry - by Arran - 10-04-2016, 03:21 AM
RE: Couple of Nationals for Terry - by Radioroslyn - 10-04-2016, 08:42 PM
RE: Couple of Nationals for Terry - by Phlogiston - 10-05-2016, 11:06 AM
RE: Couple of Nationals for Terry - by TA Forbes - 10-07-2016, 08:49 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>