Halson Radio

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Halson Radio

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

#16

10-05-2016, 04:29 PM

Here is a simple diagram of the volume ckt I have some unknowns
1. the 460ohm resistor the original was a flex resistor that was open. I found a section that had continuity and measured it then calculated that this is what it should be for the length, not sure if I'm right.
2 Vol pot was not original and was burned up I have used a 30k also with out any difference. Currently a 10k is this ok?
3 All the G2 pin 3 are tied in series
If I attach my ant to G1 of the 24A it plays great lots of stations.
What now?

Eric

Find

« Next Oldest | Next Newest »

Messages In This Thread

Halson Radio - by Eric - 10-03-2016, 10:05 AM

RE: Halson Radio - by morzh - 10-03-2016, 11:37 AM

RE: Halson Radio - by Eric - 10-03-2016, 03:49 PM

RE: Halson Radio - by morzh - 10-03-2016, 05:16 PM

RE: Halson Radio - by Eric - 10-03-2016, 07:39 PM

RE: Halson Radio - by KCMike - 10-03-2016, 05:49 PM

RE: Halson Radio - by Eric - 10-03-2016, 07:38 PM

RE: Halson Radio - by Radioroslyn - 10-03-2016, 07:27 PM

RE: Halson Radio - by Kenneth F. Besso Jr. - 10-03-2016, 09:02 PM

RE: Halson Radio - by morzh - 10-03-2016, 09:32 PM

RE: Halson Radio - by Arran - 10-04-2016, 03:38 AM

RE: Halson Radio - by morzh - 10-04-2016, 07:58 AM

RE: Halson Radio - by OldRestorer - 10-04-2016, 08:58 AM

RE: Halson Radio - by morzh - 10-04-2016, 12:38 PM

RE: Halson Radio - by Eric - 10-04-2016, 02:36 PM

RE: Halson Radio - by Eric - 10-05-2016, 04:29 PM

RE: Halson Radio - by Radioroslyn - 10-05-2016, 05:58 PM

RE: Halson Radio - by Eric - 10-06-2016, 05:48 PM

RE: Halson Radio - by Radioroslyn - 10-06-2016, 06:22 PM

RE: Halson Radio - by Eric - 10-07-2016, 01:28 PM

RE: Halson Radio - by Radioroslyn - 10-07-2016, 01:54 PM

RE: Halson Radio - by TA Forbes - 10-07-2016, 08:51 PM

RE: Halson Radio - by Arran - 10-11-2016, 04:20 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5498 online users. [Complete List]
» 4 Member(s) | 5494 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me