1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
1929 Philco 95 Dial cable guide?
PhilcoPhan1936
Jeff W.
******
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro State, Province, Country: AR
#15

10-13-2016, 02:25 AM
(10-12-2016, 04:28 AM)Arran Wrote:   Is the dial cable actually broken or did it just slip off on one end? Or did one of the loops come undone? It looks like the original stuff was a bronze dial cable, AES used to sell that stuff for repairing Radiola 18s and other such sets, I don't know if they still carry it though. This looks close but probably too thick:

https://www.amazon.com/gp/product/B0013H...EMF29PNDQA

Regards
Arran

Arran,

Yes, the dial cable is broken. There's a frayed end hanging loose.
It'll be a while before I get around to working on this, but I like to get my parts and ducks in a row before I start on a radio. Thanks for the link. I'll check it out.
Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Find
« Next Oldest | Next Newest »


Messages In This Thread
RE: 1929 Philco 95 Dial cable guide? - by Kestas - 09-07-2016, 04:55 PM
RE: 1929 Philco 95 Dial cable guide? - by Kestas - 10-11-2016, 02:57 PM
RE: 1929 Philco 95 Dial cable guide? - by Chris h - 09-12-2016, 07:00 PM
RE: 1929 Philco 95 Dial cable guide? - by Arran - 10-12-2016, 04:28 AM
RE: 1929 Philco 95 Dial cable guide? - by PhilcoPhan1936 - 10-13-2016, 02:25 AM
RE: 1929 Philco 95 Dial cable guide? - by Kestas - 10-12-2016, 05:16 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5193 online users. [Complete List]
» 3 Member(s) | 5190 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration