RCA Victrola V-210

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

RCA Victrola V-210

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

#19

10-13-2016, 12:17 PM

Ok, Replaced some wires that were rotted. Capacitor Replacement about 80% complete. Finding a lot of Resistors way out of spec.. Still do not know what to do with this Cap? Should I replace or leave as is??

[Image: http://i292.photobucket.com/albums/mm38/...vcghcg.jpg]

Skip...

Find

« Next Oldest | Next Newest »

Messages In This Thread

RCA Victrola V-210 - by vecher - 09-09-2016, 11:59 AM

RE: RCA Victrola V-210 - by vecher - 09-09-2016, 02:43 PM

RE: RCA Victrola V-210 - by klondike98 - 09-09-2016, 02:57 PM

RE: RCA Victrola V-210 - by vecher - 09-09-2016, 07:31 PM

RE: RCA Victrola V-210 - by vecher - 09-18-2016, 10:59 PM

RE: RCA Victrola V-210 - by OldRestorer - 09-21-2016, 08:35 PM

RE: RCA Victrola V-210 - by morzh - 09-22-2016, 08:22 AM

RE: RCA Victrola V-210 - by vecher - 09-22-2016, 08:19 PM

RE: RCA Victrola V-210 - by vecher - 09-22-2016, 08:20 PM

RE: RCA Victrola V-210 - by Arran - 09-23-2016, 04:11 AM

RE: RCA Victrola V-210 - by morzh - 09-23-2016, 09:20 AM

RE: RCA Victrola V-210 - by Arran - 09-24-2016, 04:46 AM

RE: RCA Victrola V-210 - by vecher - 09-23-2016, 01:45 PM

RE: RCA Victrola V-210 - by morzh - 09-24-2016, 09:50 AM

RE: RCA Victrola V-210 - by vecher - 09-24-2016, 08:50 PM

RE: RCA Victrola V-210 - by vecher - 09-24-2016, 08:58 PM

RE: RCA Victrola V-210 - by KCMike - 09-24-2016, 09:09 PM

RE: RCA Victrola V-210 - by vecher - 09-24-2016, 09:55 PM

RE: RCA Victrola V-210 - by vecher - 10-13-2016, 12:17 PM

RE: RCA Victrola V-210 - by Radioroslyn - 10-13-2016, 03:13 PM

RE: RCA Victrola V-210 - by vecher - 10-13-2016, 09:23 PM

RE: RCA Victrola V-210 - by vecher - 10-15-2016, 12:28 AM

RE: RCA Victrola V-210 - by vecher - 10-16-2016, 10:35 AM

RE: RCA Victrola V-210 - by vecher - 10-17-2016, 11:12 PM

RE: RCA Victrola V-210 - by vecher - 10-18-2016, 03:31 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

Who's Online

There are currently 3634 online users. [Complete List]
» 2 Member(s) | 3632 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me