Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA Victrola V-210
#23

Ok, Volume control cleaned.. Working great now. Alignment went with out a hitch..RX great on SW and Broadcast band..

I need to put back in cabinet to do the OSC alignment. Due to the Glass not coming out with radio.. No big deal.. Thanks next..

Wish I could fine someone to do the Cabinet..

So on to the next after I get the OSC and tracking done..

Probably my Philco 46-350 or 46-1203 next.. Not sure which one..

Skip...


Messages In This Thread
RCA Victrola V-210 - by vecher - 09-09-2016, 11:59 AM
RE: RCA Victrola V-210 - by vecher - 09-09-2016, 02:43 PM
RE: RCA Victrola V-210 - by klondike98 - 09-09-2016, 02:57 PM
RE: RCA Victrola V-210 - by vecher - 09-09-2016, 07:31 PM
RE: RCA Victrola V-210 - by vecher - 09-18-2016, 10:59 PM
RE: RCA Victrola V-210 - by OldRestorer - 09-21-2016, 08:35 PM
RE: RCA Victrola V-210 - by morzh - 09-22-2016, 08:22 AM
RE: RCA Victrola V-210 - by vecher - 09-22-2016, 08:19 PM
RE: RCA Victrola V-210 - by vecher - 09-22-2016, 08:20 PM
RE: RCA Victrola V-210 - by Arran - 09-23-2016, 04:11 AM
RE: RCA Victrola V-210 - by morzh - 09-23-2016, 09:20 AM
RE: RCA Victrola V-210 - by Arran - 09-24-2016, 04:46 AM
RE: RCA Victrola V-210 - by vecher - 09-23-2016, 01:45 PM
RE: RCA Victrola V-210 - by morzh - 09-24-2016, 09:50 AM
RE: RCA Victrola V-210 - by vecher - 09-24-2016, 08:50 PM
RE: RCA Victrola V-210 - by vecher - 09-24-2016, 08:58 PM
RE: RCA Victrola V-210 - by KCMike - 09-24-2016, 09:09 PM
RE: RCA Victrola V-210 - by vecher - 09-24-2016, 09:55 PM
RE: RCA Victrola V-210 - by vecher - 10-13-2016, 12:17 PM
RE: RCA Victrola V-210 - by Radioroslyn - 10-13-2016, 03:13 PM
RE: RCA Victrola V-210 - by vecher - 10-13-2016, 09:23 PM
RE: RCA Victrola V-210 - by vecher - 10-15-2016, 12:28 AM
RE: RCA Victrola V-210 - by vecher - 10-16-2016, 10:35 AM
RE: RCA Victrola V-210 - by vecher - 10-17-2016, 11:12 PM
RE: RCA Victrola V-210 - by vecher - 10-18-2016, 03:31 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM

[-]
Who's Online
There are currently 3020 online users. [Complete List]
» 1 Member(s) | 3019 Guest(s)
Avatar

>