Hallicrafters S-38A

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Hallicrafters S-38A

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

10-21-2016, 03:13 PM

Ok, Capacitor Replacement coming along nicely.. Next question has anyone wired in a band switch before.. Trying to figure out best way. Should I populate the switch with wires and then solder to where they should go? or just try to use existing wires .. Problem is on the bottom contacts they are very hard to get to...

Not a lot of room to get wires to bottom..

But if I put all new wires on switch then I have to solder to some coils and do not want to maybe break the connections??

Any Clue Anyone??

Skip...

Find

« Next Oldest | Next Newest »

Messages In This Thread

Hallicrafters S-38A - by vecher - 10-17-2016, 07:32 PM

RE: Hallicrafters S-38A - by Arran - 10-18-2016, 06:34 AM

RE: Hallicrafters S-38A - by vecher - 10-18-2016, 11:16 AM

RE: Hallicrafters S-38A - by vecher - 10-20-2016, 08:51 PM

RE: Hallicrafters S-38A - by vecher - 10-21-2016, 03:13 PM

RE: Hallicrafters S-38A - by Radioroslyn - 10-21-2016, 04:45 PM

RE: Hallicrafters S-38A - by vecher - 10-21-2016, 07:00 PM

RE: Hallicrafters S-38A - by vecher - 10-23-2016, 11:28 PM

RE: Hallicrafters S-38A - by Joe Rossi - 11-08-2016, 10:02 AM

RE: Hallicrafters S-38A - by Radioroslyn - 10-24-2016, 10:38 AM

RE: Hallicrafters S-38A - by vecher - 10-24-2016, 03:04 PM

RE: Hallicrafters S-38A - by vecher - 10-24-2016, 11:30 PM

RE: Hallicrafters S-38A - by vecher - 10-25-2016, 07:14 PM

RE: Hallicrafters S-38A - by vecher - 10-25-2016, 09:41 PM

RE: Hallicrafters S-38A - by KCMike - 10-25-2016, 09:50 PM

RE: Hallicrafters S-38A - by vecher - 10-27-2016, 12:01 AM

RE: Hallicrafters S-38A - by vecher - 11-08-2016, 01:07 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me