1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 60 alignment help
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

10-31-2016, 04:24 PM
Well you should be hearing a 400cy tone. Try connecting the sg to the grid cap of the 78 tube and adj #4 for max signal at 460kc/400cy tone heard from the spkr. You didn't switch the 77 and 75 around?? It will fit but won't work.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 60 alignment help - by Solamar - 10-28-2016, 07:18 PM
RE: Philco 60 alignment help - by Radioroslyn - 10-28-2016, 08:34 PM
RE: Philco 60 alignment help - by Solamar - 10-31-2016, 03:55 PM
RE: Philco 60 alignment help - by Radioroslyn - 10-31-2016, 04:24 PM
RE: Philco 60 alignment help - by Solamar - 10-31-2016, 04:39 PM
RE: Philco 60 alignment help - by Radioroslyn - 10-31-2016, 06:30 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 01:39 PM
RE: Philco 60 alignment help - by Radioroslyn - 11-02-2016, 03:07 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 03:59 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:00 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:09 PM
RE: Philco 60 alignment help - by Radioroslyn - 11-02-2016, 04:57 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:35 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4621 online users. [Complete List]
» 4 Member(s) | 4617 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration