1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 60 alignment help
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#6

10-31-2016, 06:30 PM
Just for grins you may want to double check your sg at 460kc on the off chance that that band isn't working. You can do this by listening for it on a working broadcast set @ 920kc (460 X2) to hear it's second harmonic.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 10-31-2016, 06:31 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 60 alignment help - by Solamar - 10-28-2016, 07:18 PM
RE: Philco 60 alignment help - by Radioroslyn - 10-28-2016, 08:34 PM
RE: Philco 60 alignment help - by Solamar - 10-31-2016, 03:55 PM
RE: Philco 60 alignment help - by Radioroslyn - 10-31-2016, 04:24 PM
RE: Philco 60 alignment help - by Solamar - 10-31-2016, 04:39 PM
RE: Philco 60 alignment help - by Radioroslyn - 10-31-2016, 06:30 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 01:39 PM
RE: Philco 60 alignment help - by Radioroslyn - 11-02-2016, 03:07 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 03:59 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:00 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:09 PM
RE: Philco 60 alignment help - by Radioroslyn - 11-02-2016, 04:57 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:35 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM

[-]
Who's Online
There are currently 4856 online users. [Complete List]
» 3 Member(s) | 4853 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration