1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
42-1015 OLD FM BAND( BOL Cabinet)
Radioroslyn
Phorum Expert
*****
Posts: 7,296
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#8

11-02-2016, 11:03 AM
(11-02-2016, 09:41 AM)davidff Wrote:  Good Morning,

I noticed that when I purchased  my 1015 it had hanging off the chassis that FM Model 1002A that shows in the hyperlink that you showed above.  Can you tell me how to hook this thing up to see if it actually still works? It is definitely the CRYSTAL DEVICES CO, unit that shows in the pictures.  Thanks for solving that mystery for me!
Dave

Link??

Did see something that's interesting, https://www.somerset.net/arm/reprints/on...ter_p1.gif
If you like to do some experimenting you could build it but just use L1, L2, C1, and the 1N34. Connect L1 to your FM ant though C1, diode anode and gnd to the Philco. Use an unmodulated signal from a signal generator across L2 @ 50mc. You can use the sg to tune across the new FM band or set the sg and use the Philco to tune most of the FM band (8mc)
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 11-02-2016, 11:34 AM by Radioroslyn.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
42-1015 OLD FM BAND( BOL Cabinet) - by davidff - 08-19-2016, 01:26 PM
RE: 42-1015 OLD FM BAND( BOL Cabinet) - by vecher - 08-19-2016, 02:21 PM
RE: 42-1015 OLD FM BAND( BOL Cabinet) - by Kestas - 08-21-2016, 08:55 PM
RE: 42-1015 OLD FM BAND( BOL Cabinet) - by Sean - 10-28-2016, 05:18 PM
RE: 42-1015 OLD FM BAND( BOL Cabinet) - by Radioroslyn - 11-02-2016, 11:03 AM
RE: 42-1015 OLD FM BAND( BOL Cabinet) - by Sean - 11-03-2016, 09:15 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; O noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it w...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM

[-]
Who's Online
There are currently 1588 online users. [Complete List]
» 2 Member(s) | 1586 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration