Philco 60 alignment help

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 60 alignment help

Solamar
Junior Member

Posts: 24
Threads: 2
Joined: Aug 2016
City: San Diego, CA

11-02-2016, 01:39 PM

(10-31-2016, 06:30 PM)Radioroslyn Wrote: Just for grins you may want to double check your sg at 460kc on the off chance that that band isn't working. You can do this by listening for it on a working broadcast set @ 920kc (460 X2) to hear it's second harmonic.

On the Philco 60 I can hear the 460kc tone at 920kc. Signal generator hooked to the control grid of 6A7, 6A7 grid clip attached, ground clip clipped to shield.

At no frequency lower than 920kc do I hear the generated tone.

Icon_thumbdown

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 60 alignment help - by Solamar - 10-28-2016, 07:18 PM

RE: Philco 60 alignment help - by Radioroslyn - 10-28-2016, 08:34 PM

RE: Philco 60 alignment help - by Solamar - 10-31-2016, 03:55 PM

RE: Philco 60 alignment help - by Radioroslyn - 10-31-2016, 04:24 PM

RE: Philco 60 alignment help - by Solamar - 10-31-2016, 04:39 PM

RE: Philco 60 alignment help - by Radioroslyn - 10-31-2016, 06:30 PM

RE: Philco 60 alignment help - by Solamar - 11-02-2016, 01:39 PM

RE: Philco 60 alignment help - by Radioroslyn - 11-02-2016, 03:07 PM

RE: Philco 60 alignment help - by Solamar - 11-02-2016, 03:59 PM

RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:00 PM

RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:09 PM

RE: Philco 60 alignment help - by Radioroslyn - 11-02-2016, 04:57 PM

RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:35 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A5...MrFixr55 — 06:48 AM

Who's Online

There are currently 5192 online users. [Complete List]
» 4 Member(s) | 5188 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me