Philco 60 alignment help

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 60 alignment help

Solamar
Junior Member

Posts: 24
Threads: 2
Joined: Aug 2016
City: San Diego, CA

#11

11-02-2016, 04:09 PM

(11-02-2016, 04:00 PM)Solamar Wrote:
(11-02-2016, 03:07 PM)RadioroslynJust as an aside, the cap on the 6A7 isn\t the control grid it Wrote: http://www.r-type.org/pdfs/6a7.pdf

So is the correct procedure to connect the freq gen to pin5?

Think I got it. Running through the whole procedure now...

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 60 alignment help - by Solamar - 10-28-2016, 07:18 PM

RE: Philco 60 alignment help - by Radioroslyn - 10-28-2016, 08:34 PM

RE: Philco 60 alignment help - by Solamar - 10-31-2016, 03:55 PM

RE: Philco 60 alignment help - by Radioroslyn - 10-31-2016, 04:24 PM

RE: Philco 60 alignment help - by Solamar - 10-31-2016, 04:39 PM

RE: Philco 60 alignment help - by Radioroslyn - 10-31-2016, 06:30 PM

RE: Philco 60 alignment help - by Solamar - 11-02-2016, 01:39 PM

RE: Philco 60 alignment help - by Radioroslyn - 11-02-2016, 03:07 PM

RE: Philco 60 alignment help - by Solamar - 11-02-2016, 03:59 PM

RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:00 PM

RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:09 PM

RE: Philco 60 alignment help - by Radioroslyn - 11-02-2016, 04:57 PM

RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:35 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM

Who's Online

There are currently 2969 online users. [Complete List]
» 1 Member(s) | 2968 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me