1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 46-1209
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#23

11-06-2016, 08:41 AM
those bakelite blocks are pretty easy. morzh has a thread on it at this LINK. I usually desolder them, take them out and heat with a hair dryer for a couple minutes and then push the guts out with a stiff wire or small allen wrench. Be sure to clip the small wires coming through the holes in the blocks. Older blocks have the wires just coming through the hole and its easy to cut. Newer blocks had the holes soldered shut so you have to work at it a bit more.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 46-1209 - by vecher - 10-31-2016, 09:41 PM
RE: Philco 46-1209 - by Arran - 11-01-2016, 05:57 AM
RE: Philco 46-1209 - by vecher - 11-01-2016, 02:21 PM
RE: Philco 46-1209 - by morzh - 11-01-2016, 03:33 PM
RE: Philco 46-1209 - by vecher - 11-01-2016, 08:35 PM
RE: Philco 46-1209 - by vecher - 11-02-2016, 03:59 PM
RE: Philco 46-1209 - by Radioroslyn - 11-02-2016, 05:20 PM
RE: Philco 46-1209 - by Kenneth F. Besso Jr. - 11-02-2016, 07:56 PM
RE: Philco 46-1209 - by Paul Philco322 - 11-02-2016, 08:02 PM
RE: Philco 46-1209 - by vecher - 11-02-2016, 11:41 PM
RE: Philco 46-1209 - by Kestas - 11-03-2016, 10:21 AM
RE: Philco 46-1209 - by vecher - 11-03-2016, 10:30 AM
RE: Philco 46-1209 - by vecher - 11-03-2016, 11:22 AM
RE: Philco 46-1209 - by vecher - 11-04-2016, 03:10 PM
RE: Philco 46-1209 - by Arran - 11-05-2016, 05:14 AM
RE: Philco 46-1209 - by vecher - 11-05-2016, 10:12 AM
RE: Philco 46-1209 - by vecher - 11-05-2016, 06:34 PM
RE: Philco 46-1209 - by Radioroslyn - 11-05-2016, 07:37 PM
RE: Philco 46-1209 - by vecher - 11-05-2016, 06:42 PM
RE: Philco 46-1209 - by vecher - 11-05-2016, 09:08 PM
RE: Philco 46-1209 - by Radioroslyn - 11-05-2016, 10:35 PM
RE: Philco 46-1209 - by vecher - 11-05-2016, 11:53 PM
RE: Philco 46-1209 - by klondike98 - 11-06-2016, 08:41 AM
RE: Philco 46-1209 - by vecher - 11-06-2016, 10:22 AM
RE: Philco 46-1209 - by klondike98 - 11-06-2016, 12:23 PM
RE: Philco 46-1209 - by vecher - 11-06-2016, 12:42 PM
RE: Philco 46-1209 - by vecher - 11-10-2016, 06:09 PM
RE: Philco 46-1209 - by KCMike - 11-10-2016, 06:16 PM
RE: Philco 46-1209 - by Nathan Slingerland - 11-10-2016, 06:16 PM
RE: Philco 46-1209 - by vecher - 11-10-2016, 10:33 PM
RE: Philco 46-1209 - by Radioroslyn - 11-10-2016, 11:28 PM
RE: Philco 46-1209 - by Kestas - 11-11-2016, 12:39 PM
RE: Philco 46-1209 - by vecher - 11-12-2016, 08:47 PM
RE: Philco 46-1209 - by vecher - 11-14-2016, 10:33 PM
RE: Philco 46-1209 - by Radioroslyn - 11-15-2016, 01:09 AM
RE: Philco 46-1209 - by vecher - 11-15-2016, 01:13 AM



Users browsing this thread: 16 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration