1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Restored 42-321
exray
Phorum Expert
*****
Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA State, Province, Country: PR
#10

09-09-2009, 06:38 PM
That cap is simply for decoupling and to isolate an external antenna from the chassis. Most any similar value would do. Your .001 would be fine. Do use a 600 volt cap though.
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Restored 42-321 - by andrekp - 08-19-2009, 09:37 AM
Re: Restored 42-321 - by codefox1 - 08-19-2009, 05:17 PM
Re: Restored 42-321 - by andrekp - 08-20-2009, 09:19 AM
Re: Restored 42-321 - by Ron Ramirez - 08-21-2009, 09:21 PM
Re: Restored 42-321 - by andrekp - 08-25-2009, 06:20 PM
Re: Restored 42-321 - by codefox1 - 08-26-2009, 01:05 AM
Re: Restored 42-321 - by Ron Ramirez - 08-26-2009, 07:46 AM
Re: Restored 42-321 - by andrekp - 09-09-2009, 01:29 PM
Re: Restored 42-321 - by Raleigh - 09-09-2009, 02:26 PM
Re: Restored 42-321 - by exray - 09-09-2009, 06:38 PM
Re: Restored 42-321 - by andrekp - 09-10-2009, 09:56 AM
Re: Restored 42-321 - by andrekp - 09-14-2009, 01:17 PM
Re: Restored 42-321 - by exray - 09-15-2009, 07:59 AM
Re: Restored 42-321 - by andrekp - 09-15-2009, 01:03 PM
Re: Restored 42-321 - by andrekp - 09-15-2009, 02:32 PM
Re: Restored 42-321 - by andrekp - 09-15-2009, 05:22 PM
Re: Restored 42-321 - by exray - 09-15-2009, 06:24 PM
Re: Restored 42-321 - by andrekp - 09-16-2009, 12:59 PM
Re: Restored 42-321 - by exray - 09-16-2009, 07:39 PM
Re: Restored 42-321 - by andrekp - 09-17-2009, 10:09 AM
Re: Restored 42-321 - by Ron Ramirez - 09-17-2009, 12:17 PM
Re: Restored 42-321 - by andrekp - 09-17-2009, 02:52 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM

[-]
Who's Online
There are currently 5472 online users. [Complete List]
» 1 Member(s) | 5471 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration