Philco 46-1209

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 46-1209

Radioroslyn
Phorum Expert

Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa

#31

11-10-2016, 10:28 PM

I use the yellow ones. The dip cap can be the wrong shape to restuff into the old cardboard tube from the old cap. The down side to using the non dip cap is if you happen to brush your soldering iron you can kiss it good bye. The dips have an epoxy coating.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 46-1209 - by vecher - 10-31-2016, 08:41 PM

RE: Philco 46-1209 - by Arran - 11-01-2016, 04:57 AM

RE: Philco 46-1209 - by vecher - 11-01-2016, 01:21 PM

RE: Philco 46-1209 - by morzh - 11-01-2016, 02:33 PM

RE: Philco 46-1209 - by vecher - 11-01-2016, 07:35 PM

RE: Philco 46-1209 - by vecher - 11-02-2016, 02:59 PM

RE: Philco 46-1209 - by Radioroslyn - 11-02-2016, 04:20 PM

RE: Philco 46-1209 - by Kenneth F. Besso Jr. - 11-02-2016, 06:56 PM

RE: Philco 46-1209 - by Paul Philco322 - 11-02-2016, 07:02 PM

RE: Philco 46-1209 - by vecher - 11-02-2016, 10:41 PM

RE: Philco 46-1209 - by Kestas - 11-03-2016, 09:21 AM

RE: Philco 46-1209 - by vecher - 11-03-2016, 09:30 AM

RE: Philco 46-1209 - by vecher - 11-03-2016, 10:22 AM

RE: Philco 46-1209 - by vecher - 11-04-2016, 02:10 PM

RE: Philco 46-1209 - by Arran - 11-05-2016, 04:14 AM

RE: Philco 46-1209 - by vecher - 11-05-2016, 09:12 AM

RE: Philco 46-1209 - by vecher - 11-05-2016, 05:34 PM

RE: Philco 46-1209 - by Radioroslyn - 11-05-2016, 06:37 PM

RE: Philco 46-1209 - by vecher - 11-05-2016, 05:42 PM

RE: Philco 46-1209 - by vecher - 11-05-2016, 08:08 PM

RE: Philco 46-1209 - by Radioroslyn - 11-05-2016, 09:35 PM

RE: Philco 46-1209 - by vecher - 11-05-2016, 10:53 PM

RE: Philco 46-1209 - by klondike98 - 11-06-2016, 07:41 AM

RE: Philco 46-1209 - by vecher - 11-06-2016, 09:22 AM

RE: Philco 46-1209 - by klondike98 - 11-06-2016, 11:23 AM

RE: Philco 46-1209 - by vecher - 11-06-2016, 11:42 AM

RE: Philco 46-1209 - by vecher - 11-10-2016, 05:09 PM

RE: Philco 46-1209 - by KCMike - 11-10-2016, 05:16 PM

RE: Philco 46-1209 - by Nathan Slingerland - 11-10-2016, 05:16 PM

RE: Philco 46-1209 - by vecher - 11-10-2016, 09:33 PM

RE: Philco 46-1209 - by Radioroslyn - 11-10-2016, 10:28 PM

RE: Philco 46-1209 - by Kestas - 11-11-2016, 11:39 AM

RE: Philco 46-1209 - by vecher - 11-12-2016, 07:47 PM

RE: Philco 46-1209 - by vecher - 11-14-2016, 09:33 PM

RE: Philco 46-1209 - by Radioroslyn - 11-15-2016, 12:09 AM

RE: Philco 46-1209 - by vecher - 11-15-2016, 12:13 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

Who's Online

There are currently 4117 online users. [Complete List]
» 2 Member(s) | 4115 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me