Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Inoperable tone controls
#10

(11-15-2016, 09:40 PM)Radioroslyn Wrote:  After having a look at the schematic it's not too bad. On the treble control if you ground the end that isn't grounded it should cut the highs out. If not there is a problem with C-201 (open) I suppose C-200 could be bad but kinda doubt it it's probably a mica. Do you have 132vdc at the top end of C-201??

Whoa, C-200 is one of the few caps that I didn't replace. C-201 is a new cap.

I see on the schematic that the plate voltage at C-201 should be 132v, I have 267 volts !! It's getting late and I'm getting that look from the wife that I'd better get away from the radio right now. In the meantime, thoughts?
Thanks,
Alan


Messages In This Thread
Inoperable tone controls - by lasurveyor - 11-15-2016, 03:44 PM
RE: Inoperable tone controls - by klondike98 - 11-15-2016, 07:11 PM
RE: Inoperable tone controls - by lasurveyor - 11-15-2016, 08:12 PM
RE: Inoperable tone controls - by lasurveyor - 11-15-2016, 08:24 PM
RE: Inoperable tone controls - by Jim Koehler - 11-15-2016, 07:28 PM
RE: Inoperable tone controls - by lasurveyor - 11-15-2016, 08:27 PM
RE: Inoperable tone controls - by Radioroslyn - 11-15-2016, 09:24 PM
RE: Inoperable tone controls - by Radioroslyn - 11-15-2016, 09:40 PM
RE: Inoperable tone controls - by lasurveyor - 11-15-2016, 10:39 PM
RE: Inoperable tone controls - by Radioroslyn - 11-15-2016, 10:56 PM
RE: Inoperable tone controls - by lasurveyor - 11-15-2016, 11:25 PM
RE: Inoperable tone controls - by klondike98 - 11-15-2016, 09:41 PM
RE: Inoperable tone controls - by Radioroslyn - 11-16-2016, 12:07 AM
RE: Inoperable tone controls - by lasurveyor - 11-16-2016, 02:10 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM

[-]
Who's Online
There are currently 6145 online users. [Complete List]
» 1 Member(s) | 6144 Guest(s)
Avatar

>