1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 19LZ
PTurney
Member
***
Posts: 69
Threads: 14
Joined: Sep 2005
City: Woburn, MA
#3

11-06-2009, 10:24 AM
Hello Joe,

Thanks for the reply. I was fairly sure that would be the case - I'm just surprised it did not occur to me earlier. The scan would be very helpful if it's not too much trouble. paul@tuberadioland.com

Thanks again,
Paul
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 19LZ - by PTurney - 11-05-2009, 08:29 PM
Re: Philco 19LZ - by jayoungs - 11-06-2009, 10:09 AM
Re: Philco 19LZ - by PTurney - 11-06-2009, 10:24 AM
Re: Philco 19LZ - by jayoungs - 11-06-2009, 03:30 PM
Re: Philco 19LZ - by gary rabbitt - 11-07-2009, 12:26 AM
Re: Philco 19LZ - by Ron Ramirez - 11-07-2009, 12:51 PM
Re: Philco 19LZ - by jayoungs - 11-08-2009, 11:28 AM
Re: Philco 19LZ - by PTurney - 11-09-2009, 10:13 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios