Precision E-200-C

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Precision E-200-C

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

11-22-2016, 12:35 AM

If your not in a hurry, I've used this for a counter:
http://www.ebay.com/itm/RF-Signal-Freque...SwpDdVUNSY
Takes about 2-3wks to get it but have ordered a couple and hasn't been any problems.
It can also can be used as a digital readout on a single conversion superhet as you can program it to + or - the IF frequency from the LO frequency. Instruction are in Chinese but there is an English YT vid on how to set in up and wire it.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

(This post was last modified: 11-22-2016, 12:39 AM by Radioroslyn.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Precision E-200-C - by Mike L - 09-17-2016, 07:48 PM

RE: Precision E-200-C - by KCMike - 09-17-2016, 09:50 PM

RE: Precision E-200-C - by Bradley Rush - 11-20-2016, 11:33 PM

RE: Precision E-200-C - by Bradley Rush - 11-21-2016, 01:34 AM

RE: Precision E-200-C - by Mike L - 11-21-2016, 08:49 PM

RE: Precision E-200-C - by KCMike - 11-21-2016, 11:44 PM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 12:35 AM

RE: Precision E-200-C - by morzh - 11-22-2016, 12:00 PM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 02:21 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 02:26 PM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 04:00 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 04:10 PM

RE: Precision E-200-C - by Mondial - 11-23-2016, 10:22 PM

RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 09:10 AM

RE: Precision E-200-C - by Mondial - 11-24-2016, 10:34 AM

RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 12:36 PM

RE: Precision E-200-C - by Mike L - 11-26-2016, 05:32 PM

RE: Precision E-200-C - by Mike L - 12-24-2016, 03:40 PM

RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 04:41 PM

RE: Precision E-200-C - by Mike L - 12-24-2016, 05:49 PM

RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 07:06 PM

RE: Precision E-200-C - by Mike L - 12-31-2016, 09:33 AM

RE: Precision E-200-C - by Radioroslyn - 01-01-2017, 12:55 AM

RE: Precision E-200-C - by Mike L - 01-01-2017, 05:27 PM

RE: Precision E-200-C - by JLuke - 07-27-2024, 12:33 PM

RE: Precision E-200-C - by DaleHCook - 07-28-2024, 11:29 AM

RE: Precision E-200-C - by RodB - 07-28-2024, 04:59 PM

View a Printable Version

Users browsing this thread: 5 Guest(s)

Recent Posts
Gilfillan Brothers Car Radio?
Is it possible that the 0Z4 is actually a 6Z4/84? Also the tubes that came with the radio may not all be the correct on...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the 5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM

Who's Online

There are currently 1989 online users. [Complete List]
» 3 Member(s) | 1986 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me