1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Speaker Cone
Bill Bacco
Member
***
Posts: 94
Threads: 9
Joined: Feb 2013
City: Monroeville, PA
#4

11-22-2016, 08:55 PM
Well I contacted Rich and he doesn't sell parts.  He just does reconing and wants $40 to recone the speaker.  I really don't want to spend that much on this radio and am looking to do it myself.

I'll ask again, does anyone know of a source for cones or for speaker surrounds?  I have found some on the internet, but I'm not sure their size is correct.

Thanks, Bill
Find
« Next Oldest | Next Newest »


Messages In This Thread
Speaker Cone - by Bill Bacco - 11-21-2016, 02:41 PM
RE: Speaker Cone - by Jim Koehler - 11-21-2016, 03:20 PM
RE: Speaker Cone - by morzh - 11-21-2016, 08:41 PM
RE: Speaker Cone - by Bill Bacco - 11-22-2016, 08:55 PM
RE: Speaker Cone - by KCMike - 11-22-2016, 10:15 PM
RE: Speaker Cone - by Bill Bacco - 11-22-2016, 11:02 PM
RE: Speaker Cone - by morzh - 11-22-2016, 11:26 PM
RE: Speaker Cone - by Mondial - 11-23-2016, 08:12 AM
RE: Speaker Cone - by morzh - 11-23-2016, 10:40 AM
RE: Speaker Cone - by Bill Bacco - 12-20-2016, 10:26 PM
RE: Speaker Cone - by Bill Bacco - 12-20-2016, 10:34 PM
RE: Speaker Cone - by morzh - 12-21-2016, 12:44 AM
RE: Speaker Cone - by Kenneth F. Besso Jr. - 12-21-2016, 06:22 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4726 online users. [Complete List]
» 2 Member(s) | 4724 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration