Precision E-200-C

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Precision E-200-C

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#14

11-24-2016, 09:10 AM

(11-23-2016, 10:22 PM)Mondial Wrote: Hey Terry, those Chinese counters look real nice to add digital readout to some of my old boatanchor receivers.

How do you program in the IF offset? Do you need a computer interface or is it done with jumpers or with pushbuttons on the PCB?

It's pretty simple two small pushbuttons on the back of the pcb. No switches or interfacing to mess with. I know a HRO that is going to get one!

https://www.youtube.com/watch?v=1_neC5Z_wEg
It just takes a few minutes to figure it out the buttons/function.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Precision E-200-C - by Mike L - 09-17-2016, 07:48 PM

RE: Precision E-200-C - by KCMike - 09-17-2016, 09:50 PM

RE: Precision E-200-C - by Bradley Rush - 11-20-2016, 11:33 PM

RE: Precision E-200-C - by Bradley Rush - 11-21-2016, 01:34 AM

RE: Precision E-200-C - by Mike L - 11-21-2016, 08:49 PM

RE: Precision E-200-C - by KCMike - 11-21-2016, 11:44 PM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 12:35 AM

RE: Precision E-200-C - by morzh - 11-22-2016, 12:00 PM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 02:21 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 02:26 PM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 04:00 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 04:10 PM

RE: Precision E-200-C - by Mondial - 11-23-2016, 10:22 PM

RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 09:10 AM

RE: Precision E-200-C - by Mondial - 11-24-2016, 10:34 AM

RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 12:36 PM

RE: Precision E-200-C - by Mike L - 11-26-2016, 05:32 PM

RE: Precision E-200-C - by Mike L - 12-24-2016, 03:40 PM

RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 04:41 PM

RE: Precision E-200-C - by Mike L - 12-24-2016, 05:49 PM

RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 07:06 PM

RE: Precision E-200-C - by Mike L - 12-31-2016, 09:33 AM

RE: Precision E-200-C - by Radioroslyn - 01-01-2017, 12:55 AM

RE: Precision E-200-C - by Mike L - 01-01-2017, 05:27 PM

RE: Precision E-200-C - by JLuke - 07-27-2024, 12:33 PM

RE: Precision E-200-C - by DaleHCook - 07-28-2024, 11:29 AM

RE: Precision E-200-C - by RodB - 07-28-2024, 04:59 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the 5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM

Who's Online

There are currently 2797 online users. [Complete List]
» 2 Member(s) | 2795 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me