Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 42-350. 42-355
#13

A couple of weeks ago I finally finished the 42-355 that was on my bench. It is a nice radio! Clearly the best audio of any of the slant-fronts I've heard. Much better than the 42-350, though I listen to that one a lot, too.

I get good sensitivity on the AM and SW bands, and on the old FM band I even pick up a station or two from the modern FM band. So far, I haven't heard any RFI on it, either

Since I set up my SSTRAN a couple of months ago, I can listen to anything I want to on the AM band, so I might not bother with the FM downcoverter.

don'tdomelikethat, did you ever get a 42-355?


Messages In This Thread
Philco 42-350. 42-355 - by don'tdomelikethat - 05-31-2009, 01:31 PM
Re: Philco 42-350. 42-355 - by Arran - 06-02-2009, 11:54 PM
Re: Philco 42-350. 42-355 - by Doug Houston - 06-03-2009, 12:02 AM
Re: Philco 42-350. 42-355 - by batterymaker - 06-08-2009, 08:37 AM
Re: Philco 42-350. 42-355 - by Arran - 06-09-2009, 08:07 PM
Re: Philco 42-350. 42-355 - by Ron Ramirez - 06-09-2009, 11:17 PM
Re: Philco 42-350. 42-355 - by BDM - 06-17-2009, 01:17 AM
Re: Philco 42-350. 42-355 - by Raleigh - 06-17-2009, 10:58 AM
Re: Philco 42-350. 42-355 - by Fred R - 06-17-2009, 11:17 AM
Re: Philco 42-350. 42-355 - by Raleigh - 06-17-2009, 12:22 PM
Re: Philco 42-350. 42-355 - by Arran - 06-25-2009, 08:58 PM
Re: Philco 42-350. 42-355 - by BDM - 06-27-2009, 05:10 PM
Re: Philco 42-350. 42-355 - by Raleigh - 10-03-2009, 01:38 AM
Re: Philco 42-350. 42-355 - by don'tdomelikethat - 10-04-2009, 12:20 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

[-]
Who's Online
There are currently 4544 online users. [Complete List]
» 3 Member(s) | 4541 Guest(s)
AvatarAvatarAvatar

>