1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco ID
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#7

11-30-2016, 02:16 PM
I noticed that this set uses a lot of Backlite Caps. Values in some are .00011 ..( 110 PF)

What type of Cap would you use for them.. I cannot seem to find that value except maybe in Silver Mica?

Plus the voltage rating seems to be 1200 volts on some..

If I do get this radio I want to have caps in stock..

Also there is a Big wire wound Resistor # 47 at 35 Ohms and 235 Ohms.. I am sure if its bad I cannot get those values.. Wattage??

Condenser Bank? .09,09,05,.5 Waht caps do yopu use for them??

Sorry for all the questions but this is the first Radio of this type for me I hope??

ANY CLUE ON WHAT TO OFFER FOR THIS RADIO?

Thanks
Skip...
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco ID - by vecher - 11-27-2016, 04:15 PM
RE: Philco ID - by Nathan Slingerland - 11-27-2016, 04:17 PM
RE: Philco ID - by Ron Ramirez - 11-27-2016, 06:43 PM
RE: Philco ID - by vecher - 11-27-2016, 09:08 PM
RE: Philco ID - by klondike98 - 11-28-2016, 08:23 AM
RE: Philco ID - by vecher - 11-28-2016, 12:21 PM
RE: Philco ID - by vecher - 11-30-2016, 02:16 PM
RE: Philco ID - by Nathan Slingerland - 11-30-2016, 02:31 PM
RE: Philco ID - by Ron Ramirez - 11-30-2016, 03:24 PM
RE: Philco ID - by vecher - 12-08-2016, 10:17 PM
RE: Philco ID - by vecher - 12-09-2016, 01:15 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently 6813 online users. [Complete List]
» 1 Member(s) | 6812 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration