Philco 46-350

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 46-350

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

12-01-2016, 10:15 PM

All, Started on this 46-350 Radio. I measured the resistor string from the 117Z3 Rectifier. R100 on diagram.

This is a Cadohm resistor on chassis. It measured high except for 1st section. .. Question is Since this for the Filament string how close does it have to be.

[Image: http://i292.photobucket.com/albums/mm38/...e5z0ys.jpg]

If its a higher resistance it would be a lower voltage which is good for 1 volt tubes but how much is too low..

I guess I cold try to replace it but what wattage would I need . Or could I just put a resistor in Parallel to get the resistance to match Then question is again what wattage resistor.. I also assume that I have to match the Caps too.

Skip...

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco 46-350 - by vecher - 12-01-2016, 10:15 PM

RE: Philco 46-350 - by Mondial - 12-01-2016, 10:42 PM

RE: Philco 46-350 - by vecher - 12-01-2016, 10:47 PM

RE: Philco 46-350 - by vecher - 12-24-2016, 12:41 AM

RE: Philco 46-350 - by Arran - 12-24-2016, 04:47 AM

RE: Philco 46-350 - by vecher - 12-25-2016, 11:55 PM

RE: Philco 46-350 - by Mondial - 12-26-2016, 12:41 AM

RE: Philco 46-350 - by vecher - 12-26-2016, 04:05 PM

RE: Philco 46-350 - by Mondial - 12-26-2016, 04:22 PM

RE: Philco 46-350 - by vecher - 12-26-2016, 05:20 PM

RE: Philco 46-350 - by Radioroslyn - 12-26-2016, 07:21 PM

RE: Philco 46-350 - by Kenneth F. Besso Jr. - 12-26-2016, 08:07 PM

RE: Philco 46-350 - by vecher - 12-26-2016, 08:15 PM

RE: Philco 46-350 - by vecher - 12-27-2016, 06:55 PM

RE: Philco 46-350 - by vecher - 12-27-2016, 07:48 PM

RE: Philco 46-350 - by vecher - 12-27-2016, 10:18 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Rogers Majestic R-646
By the way, the bypass you suggested is a rare solution in some circuits. For example, this schematics solution is used...Vlad95 — 01:43 PM
Rogers Majestic R-646
No, you are wrong, because you did not know the details. Unfortunately, only ONE winding out of six is intact in both t...Vlad95 — 01:14 PM
Rogers Majestic R-646
The output 45s are still in push-pull because the transformer secondary winding is still in the grid circuit providing o...RodB — 11:52 AM
Rogers Majestic R-646
Thanks RodB for the help. But this is not a real solution to this situation, not even a temporary one. Because the firs...Vlad95 — 11:34 AM
Philco Model 16 wiring question
I was going to check the voltages as you suggested and hooked it up to my dim bulb. It appears I have a short. The bul...bobclausen — 10:34 AM
Rogers Majestic R-646
You can bypass the interstage transformer by disconnecting the primary, connect a load resistor of about 10k - 20k to th...RodB — 09:40 AM
HiFi (Chifi) tube amp build - but my own design.
So, here's Prince on stage halfway through Purple Rain when he stoops down to his tech and says "Rod, pull out that...RodB — 09:17 AM
Rogers Majestic R-646
Today I finished inspecting all the parts. The result is not very pleasing. The first positive news: 1) The power tr...Vlad95 — 11:40 PM
HiFi (Chifi) tube amp build - but my own design.
Well, found muh culprit. After using socket test adapters and finding voltages all ok, swapping 6V6s, no avail, swapped ...TV MAN — 11:18 PM
HiFi (Chifi) tube amp build - but my own design.
Well, maybe - maybe not :lol: It's been an interesting project so far! Something so simple, yet so cranky. The 1st one ...TV MAN — 05:12 PM

Who's Online

There are currently 976 online users. [Complete List]
» 1 Member(s) | 975 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me