1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco ID
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#10

12-08-2016, 10:17 PM
Ok, After checking on the OSC and antenna coils. They appear to be open..

Transformer looked OK Didn't check the IF cans..

Since I cannot rewind coils and its sounds like a PITA.. I guess I will pass on the Radio.. Unless I can maybe talk Terry into rewinding coils???

If not It will be available at the get together this Sun for Terry and Friends,,

Skip..
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco ID - by vecher - 11-27-2016, 04:15 PM
RE: Philco ID - by Nathan Slingerland - 11-27-2016, 04:17 PM
RE: Philco ID - by Ron Ramirez - 11-27-2016, 06:43 PM
RE: Philco ID - by vecher - 11-27-2016, 09:08 PM
RE: Philco ID - by klondike98 - 11-28-2016, 08:23 AM
RE: Philco ID - by vecher - 11-28-2016, 12:21 PM
RE: Philco ID - by vecher - 11-30-2016, 02:16 PM
RE: Philco ID - by Nathan Slingerland - 11-30-2016, 02:31 PM
RE: Philco ID - by Ron Ramirez - 11-30-2016, 03:24 PM
RE: Philco ID - by vecher - 12-08-2016, 10:17 PM
RE: Philco ID - by vecher - 12-09-2016, 01:15 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4732 online users. [Complete List]
» 2 Member(s) | 4730 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration