1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Ron's Philco 37-640 Restoration
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#34

12-09-2016, 11:28 PM
The weekend is here again, so now I can work some more on this chassis.

Tonight, I hit the aluminum can electrolytic with heat from the heat gun until I was able to pull out the twist-lock electrolytic inside:

[Image: http://www.philcoradio.com/images/phorum/37640_039.jpg]

Next, I installed two new electrolytics (both 10 uF, one @ 450 VDC and the other @ 50 VDC).

[Image: http://www.philcoradio.com/images/phorum/37640_040.jpg]

The can had a tapered portion near the bottom. I cut just above the taper so that I would be able to add a little glue and then push the cut pieces together:

[Image: http://www.philcoradio.com/images/phorum/37640_041.jpg]

To be continued tomorrow after the glue dries.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »


Messages In This Thread
Ron's Philco 37-640 Restoration - by Ron Ramirez - 11-27-2016, 02:21 PM
RE: Ron's Philco 37-640 Restoration - by morzh - 11-27-2016, 03:24 PM
RE: Ron's Philco 37-640 Restoration - by sam - 11-27-2016, 06:56 PM
RE: Ron's Philco 37-640 Restoration - by sam - 11-27-2016, 07:12 PM
RE: Ron's Philco 37-640 Restoration - by Arran - 11-29-2016, 05:59 AM
RE: Ron's Philco 37-640 Restoration - by Arran - 12-02-2016, 12:33 AM
RE: Ron's Philco 37-640 Restoration - by morzh - 12-04-2016, 10:12 PM
RE: Ron's Philco 37-640 Restoration - by morzh - 12-04-2016, 10:35 PM
RE: Ron's Philco 37-640 Restoration - by Ron Ramirez - 12-09-2016, 11:28 PM
RE: Ron's Philco 37-640 Restoration - by GarySP - 12-12-2016, 10:55 PM
RE: Ron's Philco 37-640 Restoration - by morzh - 12-12-2016, 11:51 PM
RE: Ron's Philco 37-640 Restoration - by morzh - 12-13-2016, 11:18 PM
RE: Ron's Philco 37-640 Restoration - by morzh - 12-14-2016, 08:57 AM
RE: Ron's Philco 37-640 Restoration - by TV MAN - 12-15-2016, 02:08 PM
RE: Ron's Philco 37-640 Restoration - by morzh - 12-17-2016, 12:07 AM
RE: Ron's Philco 37-640 Restoration - by morzh - 12-17-2016, 12:26 AM
RE: Ron's Philco 37-640 Restoration - by Chris h - 12-17-2016, 10:47 AM
RE: Ron's Philco 37-640 Restoration - by morzh - 12-17-2016, 11:56 AM
RE: Ron's Philco 37-640 Restoration - by TV MAN - 12-17-2016, 01:36 PM
RE: Ron's Philco 37-640 Restoration - by morzh - 12-17-2016, 02:29 PM
RE: Ron's Philco 37-640 Restoration - by morzh - 12-17-2016, 02:30 PM
RE: Ron's Philco 37-640 Restoration - by morzh - 12-17-2016, 07:45 PM
RE: Ron's Philco 37-640 Restoration - by KCMike - 12-18-2016, 10:25 PM
RE: Ron's Philco 37-640 Restoration - by TV MAN - 12-20-2016, 11:23 AM
RE: Ron's Philco 37-640 Restoration - by bmheise - 09-24-2019, 01:30 AM
RE: Ron's Philco 37-640 Restoration - by harley92 - 01-30-2020, 06:27 PM
RE: Ron's Philco 37-640 Restoration - by oldcoot - 12-10-2021, 10:31 PM



Users browsing this thread: 8 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration