1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-650PX for a newbie
magrade
Junior Member
**
Posts: 3
Threads: 1
Joined: Dec 2016
City: skippack P.A.
#4

12-12-2016, 11:11 PM
appreciate all of this so far, will definitely read and look at all of these suggestions and let you know. i do have a multimeter but do not know how to use it. i know basics on soldering and have done soldering of capacitors on boards on modern tv's but this is a completely different animal. i look forward to learning as i go.
Find
« Next Oldest | Next Newest »


Messages In This Thread
37-650PX for a newbie - by magrade - 12-12-2016, 07:55 PM
RE: 37-650PX for a newbie - by morzh - 12-12-2016, 09:22 PM
RE: 37-650PX for a newbie - by klondike98 - 12-12-2016, 09:26 PM
RE: 37-650PX for a newbie - by magrade - 12-12-2016, 11:11 PM
RE: 37-650PX for a newbie - by morzh - 12-12-2016, 11:50 PM
RE: 37-650PX for a newbie - by NostalgiaRadioTime - 12-13-2016, 01:33 AM
RE: 37-650PX for a newbie - by magrade - 12-13-2016, 02:56 PM
RE: 37-650PX for a newbie - by morzh - 12-13-2016, 06:36 PM
RE: 37-650PX for a newbie - by TV MAN - 12-23-2016, 12:54 PM
RE: 37-650PX for a newbie - by vecher - 12-26-2016, 08:23 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4838 online users. [Complete List]
» 2 Member(s) | 4836 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration