1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco 610 speaker issues
keith49vj3
Member
***
Posts: 157
Threads: 36
Joined: Dec 2009
City: Johnston, IA
#14

12-17-2016, 06:43 PM
My last repair seemed to work and the more I played it the less it buzzed.  While replacing the wires I accidentally knocked it off my bench.  If I had let it fall it would have landed on my foam rubber floor mat undamaged but thanks to my cat-like reflexes I caught it destroying the cone in the process.  It's now going out the Sound Remedy for a recone.
Keith
Find
« Next Oldest | Next Newest »


Messages In This Thread
philco 610 speaker issues - by keith49vj3 - 12-10-2016, 07:55 PM
RE: philco 610 speaker issues - by klondike98 - 12-10-2016, 07:59 PM
RE: philco 610 speaker issues - by morzh - 12-10-2016, 09:05 PM
RE: philco 610 speaker issues - by keith49vj3 - 12-10-2016, 10:54 PM
RE: philco 610 speaker issues - by klondike98 - 12-10-2016, 11:10 PM
RE: philco 610 speaker issues - by Jim Koehler - 12-11-2016, 10:08 AM
RE: philco 610 speaker issues - by keith49vj3 - 12-11-2016, 01:52 PM
RE: philco 610 speaker issues - by klondike98 - 12-11-2016, 02:09 PM
RE: philco 610 speaker issues - by keith49vj3 - 12-11-2016, 04:20 PM
RE: philco 610 speaker issues - by klondike98 - 12-11-2016, 04:24 PM
RE: philco 610 speaker issues - by keith49vj3 - 12-14-2016, 09:36 PM
RE: philco 610 speaker issues - by morzh - 12-14-2016, 11:23 PM
RE: philco 610 speaker issues - by TV MAN - 12-15-2016, 10:05 AM
RE: philco 610 speaker issues - by keith49vj3 - 12-17-2016, 06:43 PM
RE: philco 610 speaker issues - by morzh - 12-17-2016, 07:41 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration