Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 60 restoration
#12

Yesterday I checked again the oscillator coil and the primary (the one on the right in the sch) between pins 2 and 3 (the one saying 3.4 Ohm) was open.
It was a real pain to unwind it - so I tried to find some information and found a place where they say it is 13-14 turns and then two others where it is 17 turns. When I counted it I counted 18 turns by looking at the turns before unwinding it but then I doubted myself as I thought I counted some turns from the coil underneath (they overlap).

So today I think I will undo what I did yesterday and rewind it with 17 turns.
If anyone knows for a fact what the number of turns is, I could use some extra info.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Philco 60 restoration - by morzh - 12-18-2016, 02:14 PM
RE: Philco 60 restoration - by vecher - 12-18-2016, 03:09 PM
RE: Philco 60 restoration - by klondike98 - 12-18-2016, 03:31 PM
RE: Philco 60 restoration - by morzh - 12-18-2016, 04:16 PM
RE: Philco 60 restoration - by vecher - 12-18-2016, 04:28 PM
RE: Philco 60 restoration - by morzh - 12-18-2016, 08:17 PM
RE: Philco 60 restoration - by vecher - 12-18-2016, 09:09 PM
RE: Philco 60 restoration - by morzh - 12-18-2016, 09:12 PM
RE: Philco 60 restoration - by klondike98 - 12-18-2016, 10:21 PM
RE: Philco 60 restoration - by morzh - 12-18-2016, 10:52 PM
RE: Philco 60 restoration - by NostalgiaRadioTime - 12-19-2016, 02:26 AM
RE: Philco 60 restoration - by morzh - 12-20-2016, 09:19 AM
RE: Philco 60 restoration - by TV MAN - 12-20-2016, 11:29 AM
RE: Philco 60 restoration - by morzh - 12-20-2016, 12:51 PM
RE: Philco 60 restoration - by morzh - 12-20-2016, 03:47 PM
RE: Philco 60 restoration - by NostalgiaRadioTime - 12-20-2016, 08:26 PM
RE: Philco 60 restoration - by morzh - 12-21-2016, 12:35 AM
RE: Philco 60 restoration - by morzh - 12-21-2016, 10:40 PM
RE: Philco 60 restoration - by Ron Ramirez - 12-22-2016, 07:09 AM
RE: Philco 60 restoration - by morzh - 12-22-2016, 09:55 AM
RE: Philco 60 restoration - by Ron Ramirez - 12-22-2016, 11:17 AM
RE: Philco 60 restoration - by morzh - 12-22-2016, 11:30 AM
RE: Philco 60 restoration - by morzh - 12-23-2016, 12:04 PM
RE: Philco 60 restoration - by morzh - 12-24-2016, 12:17 AM
RE: Philco 60 restoration - by morzh - 12-24-2016, 01:45 PM
RE: Philco 60 restoration - by Ron Ramirez - 12-24-2016, 01:48 PM
RE: Philco 60 restoration - by Nathan Slingerland - 12-24-2016, 02:06 PM
RE: Philco 60 restoration - by morzh - 12-24-2016, 03:33 PM
RE: Philco 60 restoration - by morzh - 12-24-2016, 09:35 PM
RE: Philco 60 restoration - by vecher - 12-24-2016, 09:39 PM
RE: Philco 60 restoration - by morzh - 12-25-2016, 06:19 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4723 online users. [Complete List]
» 2 Member(s) | 4721 Guest(s)
AvatarAvatar

>