Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Philco 60 restoration
#20

No I am still using heat. Same thing, heat up the walls and the top, and use blunt pin (I am using a small Allen wrench) to push it out. This time after repeated heating I was pushing with all my might and after 5th or 6th attempt it would start to move, barely. I was able to push out 3 out 5 as a block but still had to dislodge tar at the top, and two came out more or less fully and a bit easier.

But...speaking of 1940-s......these are 30-s...no? And...did they actually used the same backelites in 40s?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Philco 60 restoration - by morzh - 12-18-2016, 02:14 PM
RE: Philco 60 restoration - by vecher - 12-18-2016, 03:09 PM
RE: Philco 60 restoration - by klondike98 - 12-18-2016, 03:31 PM
RE: Philco 60 restoration - by morzh - 12-18-2016, 04:16 PM
RE: Philco 60 restoration - by vecher - 12-18-2016, 04:28 PM
RE: Philco 60 restoration - by morzh - 12-18-2016, 08:17 PM
RE: Philco 60 restoration - by vecher - 12-18-2016, 09:09 PM
RE: Philco 60 restoration - by morzh - 12-18-2016, 09:12 PM
RE: Philco 60 restoration - by klondike98 - 12-18-2016, 10:21 PM
RE: Philco 60 restoration - by morzh - 12-18-2016, 10:52 PM
RE: Philco 60 restoration - by NostalgiaRadioTime - 12-19-2016, 02:26 AM
RE: Philco 60 restoration - by morzh - 12-20-2016, 09:19 AM
RE: Philco 60 restoration - by TV MAN - 12-20-2016, 11:29 AM
RE: Philco 60 restoration - by morzh - 12-20-2016, 12:51 PM
RE: Philco 60 restoration - by morzh - 12-20-2016, 03:47 PM
RE: Philco 60 restoration - by NostalgiaRadioTime - 12-20-2016, 08:26 PM
RE: Philco 60 restoration - by morzh - 12-21-2016, 12:35 AM
RE: Philco 60 restoration - by morzh - 12-21-2016, 10:40 PM
RE: Philco 60 restoration - by Ron Ramirez - 12-22-2016, 07:09 AM
RE: Philco 60 restoration - by morzh - 12-22-2016, 09:55 AM
RE: Philco 60 restoration - by Ron Ramirez - 12-22-2016, 11:17 AM
RE: Philco 60 restoration - by morzh - 12-22-2016, 11:30 AM
RE: Philco 60 restoration - by morzh - 12-23-2016, 12:04 PM
RE: Philco 60 restoration - by morzh - 12-24-2016, 12:17 AM
RE: Philco 60 restoration - by morzh - 12-24-2016, 01:45 PM
RE: Philco 60 restoration - by Ron Ramirez - 12-24-2016, 01:48 PM
RE: Philco 60 restoration - by Nathan Slingerland - 12-24-2016, 02:06 PM
RE: Philco 60 restoration - by morzh - 12-24-2016, 03:33 PM
RE: Philco 60 restoration - by morzh - 12-24-2016, 09:35 PM
RE: Philco 60 restoration - by vecher - 12-24-2016, 09:39 PM
RE: Philco 60 restoration - by morzh - 12-25-2016, 06:19 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM
54C Complete Teardown/Rebuild
Richard, Had grabbed it already but thank you just the same.  I find myself wanting to find some way to block out the...glyphmon — 12:03 AM
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting.  IF alignment went great, almost all was already spot-on.  Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project.  O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today.  Soldered one in and had a successful first power-up.  No magic smoke escaped and it tunes in...glyphmon — 09:53 PM

[-]
Who's Online
There are currently no members online.

>