1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
capacitor question?
Guest
Unregistered
 
#7

11-11-2009, 02:39 PM
thank you for the advice Gary I have been going to sites that teach how to read a wiring diagram and am learning the symbols and stuff. I will take a pic of the underneath and see if anyone can see where I might have gone wrong. thank you for your help. Shawn
« Next Oldest | Next Newest »


Messages In This Thread
capacitor question? - by Guest - 10-31-2009, 05:51 PM
Re: capacitor question? - by Alan Douglas - 10-31-2009, 09:18 PM
Re: capacitor question? - by Guest - 11-01-2009, 08:03 AM
Re: capacitor question? - by codefox1 - 11-01-2009, 01:26 PM
Re: capacitor question? - by Guest - 11-01-2009, 05:02 PM
Re: capacitor question? - by gary rabbitt - 11-07-2009, 01:04 AM
Re: capacitor question? - by Guest - 11-11-2009, 02:39 PM
Re: capacitor question? - by Alan Douglas - 11-12-2009, 05:22 PM
Re: capacitor question? - by Guest - 11-17-2009, 03:28 PM
Re: capacitor question? - by exray - 11-19-2009, 08:02 AM
Re: capacitor question? - by Ron Ramirez - 11-19-2009, 09:44 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5954 online users. [Complete List]
» 2 Member(s) | 5952 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration