Several Issues with 630X

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Several Issues with 630X

philconerd
Member

Posts: 60
Threads: 14
Joined: Oct 2008
City: Pequot Lakes, MN

01-03-2017, 01:40 PM

Okay, thanks for the reply.

Yes, the 75 tube does have a tall shield around it that covers the grid cap.

So far I don't notice anything strange with the oscillator tube but I will keep an eye on it. I had to replace the 3 rubber grommets under the tuning cap and while replacing them I had to move wires around to reach the fasteners under the chassis. So I am watching for any possible changes in performance caused by any moved wires.

G.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Several Issues with 630X - by philconerd - 01-03-2017, 11:03 AM

RE: Several Issues with 630X - by morzh - 01-03-2017, 11:17 AM

RE: Several Issues with 630X - by philconerd - 01-03-2017, 01:40 PM

RE: Several Issues with 630X - by morzh - 01-03-2017, 01:57 PM

RE: Several Issues with 630X - by philconerd - 01-03-2017, 04:12 PM

RE: Several Issues with 630X - by morzh - 01-03-2017, 05:07 PM

RE: Several Issues with 630X - by philconerd - 01-03-2017, 10:34 PM

RE: Several Issues with 630X - by philconerd - 01-05-2017, 04:46 PM

RE: Several Issues with 630X - by Mondial - 01-05-2017, 05:59 PM

RE: Several Issues with 630X - by philconerd - 01-05-2017, 07:08 PM

RE: Several Issues with 630X - by philconerd - 02-09-2017, 01:47 PM

RE: Several Issues with 630X - by Mondial - 02-09-2017, 05:45 PM

RE: Several Issues with 630X - by philconerd - 02-09-2017, 06:06 PM

RE: Several Issues with 630X - by Ron Ramirez - 02-09-2017, 08:13 PM

RE: Several Issues with 630X - by philconerd - 02-09-2017, 10:16 PM

RE: Several Issues with 630X - by morzh - 02-09-2017, 11:16 PM

RE: Several Issues with 630X - by Mondial - 02-10-2017, 09:34 AM

RE: Several Issues with 630X - by morzh - 02-10-2017, 09:48 AM

RE: Several Issues with 630X - by Ron Ramirez - 02-10-2017, 11:16 AM

RE: Several Issues with 630X - by PhilcoMike - 02-14-2017, 03:21 PM

RE: Several Issues with 630X - by morzh - 02-10-2017, 11:34 AM

RE: Several Issues with 630X - by philconerd - 02-13-2017, 06:03 PM

RE: Several Issues with 630X - by morzh - 02-13-2017, 06:14 PM

RE: Several Issues with 630X - by Kenneth F. Besso Jr. - 02-14-2017, 07:30 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

Who's Online

There are currently 3464 online users. [Complete List]
» 2 Member(s) | 3462 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me