1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 116-122 Console
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

01-04-2017, 10:21 PM
I had a similar problem with the 660L. It ended up being a bad tube socket (one of the 42 output tubes). Ungrounding the filter cans may give you a clue. Also removing the mounting screw from the bakelite blocks to unground them my help too. Seems like the issue is in the HV. If you pull the 5Z3 and power it up with 120v ac all the other tube s light and dials lamps??
> Would disconnecting an electrolytic, one at a time cause any harm?
No the set will just hum but doesn't hurt any thing.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 01-04-2017, 10:24 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 116-122 Console - by Crist Rigotti - 01-04-2017, 09:31 PM
RE: Philco 116-122 Console - by Radioroslyn - 01-04-2017, 10:21 PM
RE: Philco 116-122 Console - by Mondial - 01-04-2017, 10:30 PM
RE: Philco 116-122 Console - by Crist Rigotti - 01-05-2017, 12:05 AM
RE: Philco 116-122 Console - by Mondial - 01-05-2017, 12:23 AM
RE: Philco 116-122 Console - by Crist Rigotti - 01-05-2017, 03:35 AM
RE: Philco 116-122 Console - by Phlogiston - 01-05-2017, 12:13 PM
RE: Philco 116-122 Console - by Mondial - 01-05-2017, 08:45 AM
RE: Philco 116-122 Console - by Crist Rigotti - 01-05-2017, 11:29 AM
RE: Philco 116-122 Console - by Mondial - 01-05-2017, 01:13 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5864 online users. [Complete List]
» 2 Member(s) | 5862 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration