Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 16X dial cord stringing
#14

See below.

   

Also read the How-To at the link below. The Phorum's looks have changed since I wrote this up, but the information is still the same:

http://philcoradio.com/phorum/showthread.php?tid=4562

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Model 16X dial cord stringing - by k6ddj - 01-04-2017, 10:59 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 11:29 AM
RE: Model 16X dial cord stringing - by KCMike - 01-05-2017, 12:26 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 01:01 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 01:11 PM
RE: Model 16X dial cord stringing - by KCMike - 01-05-2017, 01:18 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 01:27 PM
RE: Model 16X dial cord stringing - by klondike98 - 01-05-2017, 01:27 PM
RE: Model 16X dial cord stringing - by KCMike - 01-05-2017, 02:12 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 02:43 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 04:36 PM
RE: Model 16X dial cord stringing - by Ron Ramirez - 01-05-2017, 04:56 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 05:23 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 4061 online users. [Complete List]
» 3 Member(s) | 4058 Guest(s)
AvatarAvatarAvatar

>