Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

GE E-71 Trouble shooting ?
#5

>We got a light layer of ice and about 1" of the white stuff, It got down to 11 last night but there saying 65-70 by thursday

Just wanted to make sure you got your fair share! We got abt 3" here but pretty cold too.

You know the drill, Make sure the bandswitch is clean and make good connection at the contacts. 
Have a look at pin 6 of the 6K8, should have HV (180v) on it on all bands. As you change bands the HV is routed though the band switch to that pin.
Check R-6,7,and 8 for drift  20% is ok.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
GE E-71 Trouble shooting ? - by Eric - 01-08-2017, 01:22 PM
RE: GE E-71 Trouble shooting ? - by KCMike - 01-08-2017, 02:10 PM
RE: GE E-71 Trouble shooting ? - by Radioroslyn - 01-08-2017, 03:37 PM
RE: GE E-71 Trouble shooting ? - by Eric - 01-08-2017, 04:53 PM
RE: GE E-71 Trouble shooting ? - by Radioroslyn - 01-08-2017, 05:14 PM
RE: GE E-71 Trouble shooting ? - by Eric - 01-08-2017, 05:31 PM
RE: GE E-71 Trouble shooting ? - by Radioroslyn - 01-08-2017, 07:38 PM
RE: GE E-71 Trouble shooting ? - by Eric - 01-09-2017, 11:57 AM
RE: GE E-71 Trouble shooting ? - by Mondial - 01-09-2017, 12:32 PM
RE: GE E-71 Trouble shooting ? - by Eric - 01-09-2017, 03:54 PM
RE: GE E-71 Trouble shooting ? - by Eric - 01-10-2017, 12:03 PM
RE: GE E-71 Trouble shooting ? - by Mondial - 01-10-2017, 12:27 PM
RE: GE E-71 Trouble shooting ? - by Eric - 01-10-2017, 02:33 PM
RE: GE E-71 Trouble shooting ? - by Mondial - 01-10-2017, 02:52 PM
RE: GE E-71 Trouble shooting ? - by Eric - 01-12-2017, 01:31 PM
RE: GE E-71 Trouble shooting ? - by Radioroslyn - 01-12-2017, 01:59 PM
RE: GE E-71 Trouble shooting ? - by klondike98 - 01-12-2017, 02:19 PM
RE: GE E-71 Trouble shooting ? - by Eric - 01-19-2017, 10:16 AM
RE: GE E-71 Trouble shooting ? - by Eliot Ness - 01-19-2017, 11:11 AM
RE: GE E-71 Trouble shooting ? - by KCMike - 01-19-2017, 11:36 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>