1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco model 610
Radioroslyn
Phorum Expert
*****
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#9

01-19-2017, 08:25 AM
Sounds like your p/s is running without a load across it. Measure the voltage across the second filter cap and that at pin 2 of the 42 tube. Methink some where the voltage is going to be very low.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco model 610 - by Radio Hound - 01-17-2017, 08:14 PM
RE: Philco model 610 - by rck46 - 01-17-2017, 08:50 PM
RE: Philco model 610 - by Radioroslyn - 01-17-2017, 11:07 PM
RE: Philco model 610 - by Radio Hound - 01-18-2017, 08:01 PM
RE: Philco model 610 - by morzh - 01-18-2017, 08:16 PM
RE: Philco model 610 - by Radio Hound - 01-19-2017, 08:09 AM
RE: Philco model 610 - by Radioroslyn - 01-18-2017, 08:21 PM
RE: Philco model 610 - by Radio Hound - 01-19-2017, 08:13 AM
RE: Philco model 610 - by Radioroslyn - 01-19-2017, 08:25 AM
RE: Philco model 610 - by Radio Hound - 01-19-2017, 12:12 PM
RE: Philco model 610 - by morzh - 01-19-2017, 12:52 PM
RE: Philco model 610 - by Radio Hound - 01-19-2017, 01:09 PM
RE: Philco model 610 - by morzh - 01-19-2017, 02:31 PM
RE: Philco model 610 - by Mondial - 01-19-2017, 06:53 PM
RE: Philco model 610 - by Radio Hound - 01-20-2017, 11:45 AM
RE: Philco model 610 - by Radio Hound - 01-23-2017, 04:54 PM
RE: Philco model 610 - by morzh - 01-23-2017, 04:59 PM
RE: Philco model 610 - by Radio Hound - 01-23-2017, 05:02 PM
RE: Philco model 610 - by morzh - 01-23-2017, 05:03 PM
RE: Philco model 610 - by Radio Hound - 01-23-2017, 05:18 PM
RE: Philco model 610 - by morzh - 01-23-2017, 05:19 PM
RE: Philco model 610 - by Radio Hound - 01-23-2017, 05:24 PM
RE: Philco model 610 - by morzh - 01-23-2017, 05:35 PM
RE: Philco model 610 - by Radio Hound - 02-07-2017, 01:16 PM
RE: Philco model 610 - by morzh - 02-07-2017, 04:15 PM
RE: Philco model 610 - by Radio Hound - 02-07-2017, 04:50 PM
RE: Philco model 610 - by Radio Hound - 02-07-2017, 04:59 PM
RE: Philco model 610 - by morzh - 02-07-2017, 06:17 PM
RE: Philco model 610 - by keith49vj3 - 02-08-2017, 08:54 PM
RE: Philco model 610 - by Radioroslyn - 02-08-2017, 09:40 PM
RE: Philco model 610 - by keith49vj3 - 02-08-2017, 09:01 PM
RE: Philco model 610 - by keith49vj3 - 02-09-2017, 07:48 AM
RE: Philco model 610 - by klondike98 - 02-09-2017, 11:07 AM
RE: Philco model 610 - by TV MAN - 02-13-2017, 01:08 PM
RE: Philco model 610 - by Radio Hound - 02-13-2017, 06:04 PM
RE: Philco model 610 - by keith49vj3 - 02-13-2017, 09:13 PM
RE: Philco model 610 - by Radio Hound - 02-16-2017, 05:24 PM
RE: Philco model 610 - by keith49vj3 - 02-13-2017, 09:33 PM
RE: Philco model 610 - by keith49vj3 - 02-14-2017, 09:56 PM
RE: Philco model 610 - by keith49vj3 - 02-15-2017, 07:46 AM
RE: Philco model 610 - by keith49vj3 - 02-16-2017, 09:22 PM
RE: Philco model 610 - by morzh - 02-16-2017, 11:56 PM
RE: Philco model 610 - by keith49vj3 - 02-17-2017, 08:13 AM
RE: Philco model 610 - by morzh - 02-17-2017, 09:58 AM
RE: Philco model 610 - by keith49vj3 - 02-19-2017, 08:23 AM
RE: Philco model 610 - by morzh - 02-19-2017, 12:08 PM
RE: Philco model 610 - by Radio Hound - 02-20-2017, 08:35 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration