1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 48-460 restoration
Bob Andersen
Phorum Expert
*****
Posts: 797
Threads: 42
Joined: Dec 2008
City: Chicago, IL
#9

01-19-2017, 01:48 PM
OK, the problem seems to be the volume potentiometer. The lowest it goes is about 7K. Unfortunately, I don't have a replacement on hand so for now I did a quick polish and I'll call it done. If the owner want's to address it in the future I'll take another whack at it.
[Image: https://c1.staticflickr.com/1/344/322563...9073_c.jpg]
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 48-460 restoration - by Bob Andersen - 12-01-2016, 06:03 PM
RE: Philco 48-460 restoration - by Bob Andersen - 12-01-2016, 06:13 PM
RE: Philco 48-460 restoration - by Radioroslyn - 12-01-2016, 06:15 PM
RE: Philco 48-460 restoration - by Bob Andersen - 12-01-2016, 06:28 PM
RE: Philco 48-460 restoration - by klondike98 - 12-01-2016, 07:04 PM
RE: Philco 48-460 restoration - by Paul Philco322 - 12-01-2016, 08:54 PM
RE: Philco 48-460 restoration - by Bob Andersen - 01-05-2017, 07:00 PM
RE: Philco 48-460 restoration - by Bob Andersen - 01-17-2017, 02:38 PM
RE: Philco 48-460 restoration - by Bob Andersen - 01-19-2017, 01:48 PM
RE: Philco 48-460 restoration - by Bob Andersen - 01-19-2017, 02:18 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

[-]
Who's Online
There are currently 3348 online users. [Complete List]
» 3 Member(s) | 3345 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration