1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Seeking advices on eliminating noise on a Philco 70-A
Guest
Unregistered
 
#3

01-13-2006, 03:08 PM
Hi Pete,

Thanks for the prompt response and advices.

As part of the troubleshooting process, the 2nd detector tube 24 was replaced and noticed no changes.

As you recommended, I will swap the cathode bias resistor, #27- the 50K with new one.


Cheers

Recepteur
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Noise in the 70 detector - by AI2V - 01-13-2006, 12:40 PM
[No subject] - by Guest - 01-13-2006, 03:08 PM
[No subject] - by PTurney - 01-13-2006, 07:20 PM
[No subject] - by Guest - 01-14-2006, 09:41 AM
[No subject] - by Guest - 01-24-2006, 05:53 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. S...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM

[-]
Who's Online
There are currently 1373 online users. [Complete List]
» 1 Member(s) | 1372 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration