Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

An Original Philco Hippo
#9

Dan;
  It seems to depend on the code number, and production run, as to what pilot lamp the Hippo models use, some use a G.E #47 or equivalent, others use a 120 V night light type bulb. I think that the sets that used a 35Z3 (Loctal) used the 120 Volt night light bulb, basically a Christmas light bulb, since the 35Z3s don't have a pilot light tap on the filament. In any event they sell LED substitutes for night light bulbs in Walmart and some other stores, that would eliminate the potential melting plastic issue these sometimes get.
Regards
Arran


Messages In This Thread
An Original Philco Hippo - by Dan Walker - 02-23-2017, 08:13 AM
RE: An Original Philco Hippo - by David - 02-23-2017, 08:38 AM
RE: An Original Philco Hippo - by morzh - 02-23-2017, 08:39 AM
RE: An Original Philco Hippo - by Dan Walker - 02-23-2017, 02:43 PM
RE: An Original Philco Hippo - by morzh - 02-23-2017, 04:37 PM
RE: An Original Philco Hippo - by Paul Philco322 - 02-23-2017, 08:38 PM
RE: An Original Philco Hippo - by Dan Walker - 02-23-2017, 10:31 PM
RE: An Original Philco Hippo - by Arran - 02-24-2017, 12:32 AM
RE: An Original Philco Hippo - by Dan Walker - 02-24-2017, 11:00 AM
RE: An Original Philco Hippo - by Dan Walker - 02-24-2017, 01:08 PM
RE: An Original Philco Hippo - by David - 02-24-2017, 07:43 PM
RE: An Original Philco Hippo - by Dan Walker - 02-24-2017, 08:51 PM
RE: An Original Philco Hippo - by Paul Philco322 - 02-24-2017, 09:52 PM
RE: An Original Philco Hippo - by morzh - 02-24-2017, 10:42 PM
RE: An Original Philco Hippo - by Arran - 02-24-2017, 10:50 PM
RE: An Original Philco Hippo - by David - 02-26-2017, 07:40 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2047 online users. [Complete List]
» 1 Member(s) | 2046 Guest(s)
Avatar

>