1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 90 Oscillator question
bdi1976
Member
***
Posts: 82
Threads: 14
Joined: Mar 2014
City: Philadelphia, PA
#21

02-24-2017, 10:38 PM
I found a new resistor which somehow drifted 50% out of tolerance in only 1 year..the 10kOhm on the antenna..was only reading 5 disconnected from the coil. Put in a new one, cleaned all tube prongs with 200 grit sand paper, and got additional sound and clarity. Still a lot of background noise though unless I screw around with that IF secondary trimmer which clears it up. Is it possible it's just alignment since I rewound the oscillator coil? I tried adjusting by hand and don't know for sure if I'm at the right KC. I have a signal generator but not familiar enough To Try to align using it
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 90 Oscillator question - by bdi1976 - 03-07-2016, 10:00 PM
RE: Philco 90 Oscillator question - by TV MAN - 03-10-2016, 10:31 AM
RE: Philco 90 Oscillator question - by bdi1976 - 03-11-2016, 09:54 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-18-2017, 01:51 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-18-2017, 07:00 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-19-2017, 12:35 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-20-2017, 10:03 PM
RE: Philco 90 Oscillator question - by sam - 02-21-2017, 12:42 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-21-2017, 05:24 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-24-2017, 10:38 PM
RE: Philco 90 Oscillator question - by bdi1976 - 03-12-2017, 05:11 PM
RE: Philco 90 Oscillator question - by bdi1976 - 03-12-2017, 07:54 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
I completed the insulation on the cabinet interior (Al foil and hi temp silicone rubber), and reglued the speaker gasket...EdHolland — 06:18 PM
HiFi (Chifi) tube amp build - but my own design.
Tim - Photos of 8 octal tube sockets. (Top and bottom) Send me a PM if you're interested.RodB — 04:11 PM
VTVM meter moves when my hand is next to it & not on
Haha! I hope so. It seemed rather lost and forgotten languishing in the frozen Northeast of England.EdHolland — 02:36 PM
VTVM meter moves when my hand is next to it & not on
Ed - it's in the Cayman's enjoying the good life.RodB — 02:14 PM
VTVM meter moves when my hand is next to it & not on
Static electricity - but the other chaps beat me to it again. I've seen this before with analogue meters. I've also ...EdHolland — 01:56 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM

[-]
Who's Online
There are currently 1165 online users. [Complete List]
» 1 Member(s) | 1164 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration