Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Question on a 50L6 tube
#5

Ok I used a Hickok 600A tester and a Heathkit IT-17.. All showed short on 5 tubes.. Doesn't seem right. But maybe all 5 are bad? I wouldn't think so But who knows..

Going to see if I have any 25L6 or similar to see what they read..

Skip..


Messages In This Thread
Question on a 50L6 tube - by vecher - 02-28-2017, 12:21 PM
RE: Question on a 50L6 tube - by morzh - 02-28-2017, 05:10 PM
RE: Question on a 50L6 tube - by TV MAN - 02-28-2017, 05:50 PM
RE: Question on a 50L6 tube - by morzh - 02-28-2017, 05:51 PM
RE: Question on a 50L6 tube - by vecher - 02-28-2017, 05:55 PM
RE: Question on a 50L6 tube - by morzh - 02-28-2017, 06:29 PM
RE: Question on a 50L6 tube - by vecher - 02-28-2017, 08:32 PM
RE: Question on a 50L6 tube - by klondike98 - 02-28-2017, 08:57 PM
RE: Question on a 50L6 tube - by vecher - 02-28-2017, 09:55 PM
RE: Question on a 50L6 tube - by morzh - 03-01-2017, 11:06 AM
RE: Question on a 50L6 tube - by Jayce - 03-01-2017, 12:32 PM
RE: Question on a 50L6 tube - by David - 03-03-2017, 06:12 PM
RE: Question on a 50L6 tube - by Paul Philco322 - 03-03-2017, 09:04 PM
RE: Question on a 50L6 tube - by rocketeer - 03-13-2017, 09:50 PM
RE: Question on a 50L6 tube - by vecher - 03-14-2017, 12:45 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently no members online.

>