How do I use an ultrasonic parts cleaner?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

How do I use an ultrasonic parts cleaner?

gregb
Senior Member

Posts: 599
Threads: 24
Joined: Jan 2014
City: Edmonton AB CA

#3

03-07-2017, 12:55 AM

I use CLR in mine and I mix the CLR 1 part CLR to 5 parts water. I let the solution warm up for five minutes before putting the tuner in. Keep a close eye on it as the CLR can damage plated surfaces if left to long. I also hang on to it with pliers and swish it around while its in there and I go for 15 to 30 seconds and then rinse in fresh water. Blow the water off with some compressed air after and you will be good to go.

Gregb

Attached Files Image(s)

03-07-2017, 12:55 AM

03-07-2017, 12:54 AM

Find

« Next Oldest | Next Newest »

Messages In This Thread

How do I use an ultrasonic parts cleaner? - by TV MAN - 03-06-2017, 10:44 PM

RE: How do I use an ultrasonic parts cleaner? - by morzh - 03-07-2017, 12:26 AM

RE: How do I use an ultrasonic parts cleaner? - by gregb - 03-07-2017, 12:55 AM

RE: How do I use an ultrasonic parts cleaner? - by TV MAN - 03-07-2017, 09:37 AM

RE: How do I use an ultrasonic parts cleaner? - by Mondial - 03-07-2017, 09:58 AM

RE: How do I use an ultrasonic parts cleaner? - by Eliot Ness - 03-07-2017, 11:41 AM

RE: How do I use an ultrasonic parts cleaner? - by John Bartley - 03-07-2017, 11:59 AM

RE: How do I use an ultrasonic parts cleaner? - by morzh - 03-07-2017, 12:06 PM

RE: How do I use an ultrasonic parts cleaner? - by Jim Dutridge - 03-07-2017, 08:57 PM

RE: How do I use an ultrasonic parts cleaner? - by TV MAN - 03-08-2017, 11:13 PM

RE: How do I use an ultrasonic parts cleaner? - by John Bartley - 03-10-2017, 08:07 AM

RE: How do I use an ultrasonic parts cleaner? - by gregb - 03-08-2017, 11:39 PM

RE: How do I use an ultrasonic parts cleaner? - by TV MAN - 03-10-2017, 11:03 PM

RE: How do I use an ultrasonic parts cleaner? - by Kestas - 03-11-2017, 04:32 PM

RE: How do I use an ultrasonic parts cleaner? - by Chris h - 03-15-2017, 01:22 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

Who's Online
There are currently no members online.