1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 90 Oscillator question
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#25

03-12-2017, 08:14 PM
Check the resistance of the ant coil primary and secondary. Both should show a low resistance like 20 ohms or less. Check the plate and screen voltage on  the rf amp should see about 200v or so. Cathode should have a low voltage maybe 5-10vdc. Acts like your ant coil is open. If you want to bring it over just give me a heads up so I can clear off the space to work on it.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 03-12-2017, 08:17 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 90 Oscillator question - by bdi1976 - 03-07-2016, 10:00 PM
RE: Philco 90 Oscillator question - by TV MAN - 03-10-2016, 10:31 AM
RE: Philco 90 Oscillator question - by bdi1976 - 03-11-2016, 09:54 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-18-2017, 01:51 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-18-2017, 07:00 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-19-2017, 12:35 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-20-2017, 10:03 PM
RE: Philco 90 Oscillator question - by sam - 02-21-2017, 12:42 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-21-2017, 05:24 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-24-2017, 10:38 PM
RE: Philco 90 Oscillator question - by bdi1976 - 03-12-2017, 05:11 PM
RE: Philco 90 Oscillator question - by bdi1976 - 03-12-2017, 07:54 PM
RE: Philco 90 Oscillator question - by Radioroslyn - 03-12-2017, 08:14 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3161 online users. [Complete List]
» 2 Member(s) | 3159 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration