Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 89 veneer missing
#6

Arran is correct, Philco used a cheep veneer on the wrap-around, toned dark to look like Walnut. It fooled a lot of people LOL.

This is a cabinet that I did a restoration on a few years ago that had been striped and stained. It had what appeared to be rotary cut Fir.

[img]<a data-flickr-embed=[/img][Image: https://c1.staticflickr.com/1/737/325853...94d9_z.jpg]" />


I use Walnut veneer on my reproduction cabinets.

Steve

M R Radios   C M Tubes


Messages In This Thread
Philco 89 veneer missing - by RadioDR401 - 03-07-2017, 08:00 PM
RE: Philco 89 veneer missing - by John Bartley - 03-08-2017, 07:12 AM
RE: Philco 89 veneer missing - by Steve Davis - 03-08-2017, 09:29 AM
RE: Philco 89 veneer missing - by Radioroslyn - 03-10-2017, 08:40 PM
RE: Philco 89 veneer missing - by Arran - 03-13-2017, 12:54 AM
RE: Philco 89 veneer missing - by Steve Davis - 03-13-2017, 09:29 PM
RE: Philco 89 veneer missing - by Arran - 03-13-2017, 09:43 PM
RE: Philco 89 veneer missing - by RadioDR401 - 03-14-2017, 10:42 AM
RE: Philco 89 veneer missing - by Steve Davis - 03-14-2017, 12:27 PM
RE: Philco 89 veneer missing - by Arran - 03-14-2017, 06:50 PM
RE: Philco 89 veneer missing - by RadioDR401 - 07-04-2017, 10:41 AM
RE: Philco 89 veneer missing - by Steve Davis - 07-04-2017, 01:07 PM
RE: Philco 89 veneer missing - by RadioDR401 - 07-05-2017, 03:28 PM
RE: Philco 89 veneer missing - by Phlogiston - 07-05-2017, 05:13 PM
RE: Philco 89 veneer missing - by RadioDR401 - 07-06-2017, 06:18 AM
RE: Philco 89 veneer missing - by Phlogiston - 07-06-2017, 09:33 AM
RE: Philco 89 veneer missing - by RadioDR401 - 08-29-2017, 11:40 AM
RE: Philco 89 veneer missing - by RadioDR401 - 09-09-2017, 02:33 PM
RE: Philco 89 veneer missing - by Phlogiston - 09-09-2017, 03:05 PM
RE: Philco 89 veneer missing - by Scott D - 09-09-2017, 04:15 PM
RE: Philco 89 veneer missing - by RadioDR401 - 03-05-2018, 04:09 PM
RE: Philco 89 veneer missing - by sdradioman - 03-05-2018, 09:07 PM
RE: Philco 89 veneer missing - by Radioroslyn - 03-05-2018, 10:46 PM
RE: Philco 89 veneer missing - by RadioDR401 - 03-06-2018, 09:49 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
RCA WV-98c
If this is R22, check the voltage on the wiper (86V). If this is R33, see if the lower pin indeed connected to GND, the ...morzh — 02:29 PM
Philco 38-2 Low Volume
Both sch, the one you showed in the beginning and the one I see on Nostalgia, show 40K for the 2nd audio plate.morzh — 02:25 PM
Model 96 cabinet veneer
I can't figure out what the first step is, let alone the final step. I have tried copying pictures from my hard drive a...TGLager — 01:40 PM
Philco 38-2 Low Volume
I managed to get some more time on this. Hi Mr. FixIT, The radio has been recapped. Many of the resistors were rep...dconant — 01:39 PM
Philco 38-2 Low Volume
Thanks guys for the help. I started looking at these points but I have to quit for the day. I will be looking into this ...dconant — 12:23 PM
RCA WV-98c
Check out this crazy zero pot operation. Touching it drives it crazy. Its rubber tipped. Also the 6al5 has no negative v...daveone23 — 12:08 PM
Philco 38-2 Low Volume
If you check all of that and still have a problem (my first inkling would be one of the 6F6s) then look at the 6J5 phase...RodB — 10:44 AM
RCA WV-98c
Those will probably depend on teh switch combination. Could you list some that you see, their values and what they sh...morzh — 10:26 AM
Model 96 cabinet veneer
You are probably skipping the final step. Once you select the photos you want and they get downloaded, the system assign...RodB — 09:36 AM
RCA WV-98c
At this point, there is no input, just internal voltages Which are incorrect and not sure what they should be.daveone23 — 09:15 AM

[-]
Who's Online
There are currently 1348 online users. [Complete List]
» 1 Member(s) | 1347 Guest(s)
Avatar

>