1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Pre-1936 Philco resistors
Steve D
Member
***
Posts: 115
Threads: 25
Joined: Jul 2006
City: Lebanon, NJ 08833
#7

03-22-2017, 05:37 PM
I've seen just heating up old resistors while soldering can make then drift up very high.  I always recheck every resistor that I touch with a soldering iron.

Steve D
Find
« Next Oldest | Next Newest »


Messages In This Thread
Pre-1936 Philco resistors - by 45philcodon - 03-21-2017, 07:05 PM
RE: Pre-1936 Philco resistors - by klondike98 - 03-21-2017, 07:16 PM
RE: Pre-1936 Philco resistors - by 45philcodon - 03-23-2017, 05:14 PM
RE: Pre-1936 Philco resistors - by Radioroslyn - 03-21-2017, 10:12 PM
RE: Pre-1936 Philco resistors - by jcassity - 03-22-2017, 01:11 PM
RE: Pre-1936 Philco resistors - by Radioroslyn - 03-22-2017, 02:00 PM
RE: Pre-1936 Philco resistors - by Steve D - 03-22-2017, 05:37 PM
RE: Pre-1936 Philco resistors - by jcassity - 03-22-2017, 09:09 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration